TFS street castings by RHP. Lead times reduced !

Lead times reduced. Have hired help to rough in the heads so I only have to do the finish work and flow testing...8)

Available starting at $2,350.00

Ported and fully assembled TFS street heat castings.

S/S intake valves
TFS juice spring package std. Flat tappet and Roller spring upgrade available for additional cost.
Rocker studs and 3/8" guideplates.
Ported to 360+/250 CFM and ready to make some serious HP.




http://trickflow.com/media/pr/400/TFS-53410001.jpg



8)
.
.
.

n/m



8)
.
.

ttt

what's the largest displacment and horsepower rating these heads will support??
Thanks,
John M.

what's the largest displacment and horsepower rating these heads will support??
Thanks,
John M.

Fully ported they will support 800 HP on a 12 to 1 stroker combo with a solid roller in the 270 @ .050" range intake duration.

Not too shabby for a small port head.



8)
.
.
.

OK thank you for the information. I guess I will have to look for other heads to allow for future growth.
Thanks again,
John M.

ttt

ttt

8)

Available starting at $2,200.00

Ported and fully assembled TFS street heat castings.

S/S intake valves
Comp flat tappet 924-16 spring package with 10 degree retainers and locks. Roller spring upgrade available for additional cost.
Rocker studs and 5/16" or 3/8" guideplates.
Ported to 360/245 CFM and ready to make some serious HP.


is the $2200 price including assembly with the above mentioned components, and what would a shipping estimate be to 33810(Lakeland,Fl)

I know it says "starting at" so I was curious...

8)

Available starting at $2,200.00

Ported and fully assembled TFS street heat castings.

S/S intake valves
Comp flat tappet 924-16 spring package with 10 degree retainers and locks. Roller spring upgrade available for additional cost.
Rocker studs and 5/16" or 3/8" guideplates.
Ported to 360/245 CFM and ready to make some serious HP.


is the $2200 price including assembly with the above mentioned components, and what would a shipping estimate be to 33810(Lakeland,Fl)

I know it says "starting at" so I was curious...

The starting at price does include comp flat tappet spring package, sinus stainless valves made in israel, rocker studs, guideplates and pc seals. I use the actual serdi cutters used by TFS to cut their seats. Kind of a budget version of sorts.

Upgrades such as roller spring package, Ferrea valves an a victor port match are available.

Shipping to florida will be about $70.00


8)

damn i wish i could sell my current motor and put these on my new one...

n/m

Upgrades such as roller spring package, Ferrea valves an a victor port match are available.


how much is that as a complete head????

Upgrades such as roller spring package, Ferrea valves an a victor port match are available.


how much is that as a complete head????

$2,650.00 covers ferrea valves, comp 954-16 roller spring package and victor port match. Flow rates are in the high 360's to low 370's intake and 245 to 255 exhaust depending on valve sizes.

You can have 2.25"/1.76" or 2.2"/1.8" ferrea's...



8)
.
.
.

2.2/ 1.8 lovin the spray :twisted:

hellofagood deal really if you think about it!

n/m

n/m

n/m

ttt

Scotty,

I have been reading the BBF forum for about 1.5 years. I must say that there is a tremendous amount of information that is put forth by experts. I thank you. I bought a '87 Mustang w/ a 545 by CHP. The engine has Probe flats with -3cc tops, Crane solid w/ .621 lift with 292 duration and 72 overlap degrees @.020. RPM range is 4200 to 7200. Stall is 4000rpm. The heads are Dove with light polish and 2.25 and 1.76 valves. BG 850 carb on a Stealth. Gears are 3.27( a little high). Exhaust is Hooker Comp with 2" tubes and 3.5" collector, exhaust pipes and mufflers.

I would like to stay with the above combination except add alum heads and some new ceramic headers. My present compression is 13.3:1 however I would like to reduce it to 11.5 to 12.5. Can I use the Street heads to get the chamber volume increased to mid 80's to low90's. Or what other options are available?

Thank you for your help.


Mike

Scotty,

I have been reading the BBF forum for about 1.5 years. I must say that there is a tremendous amount of information that is put forth by experts. I thank you. I bought a '87 Mustang w/ a 545 by CHP. The engine has Probe flats with -3cc tops, Crane solid w/ .621 lift with 292 duration and 72 overlap degrees @.020. RPM range is 4200 to 7200. Stall is 4000rpm. The heads are Dove with light polish and 2.25 and 1.76 valves. BG 850 carb on a Stealth. Gears are 3.27( a little high). Exhaust is Hooker Comp with 2" tubes and 3.5" collector, exhaust pipes and mufflers.

I would like to stay with the above combination except add alum heads and some new ceramic headers. My present compression is 13.3:1 however I would like to reduce it to 11.5 to 12.5. Can I use the Street heads to get the chamber volume increased to mid 80's to low90's. Or what other options are available?

Thank you for your help.


Mike


Mike,

The TFS streets have a 72 to 74 cc chamber which is a tic smaller than most D0VE castings.

The only large chamber casting usable on a stroker is the edelbrock...


8)
.
.
.
.
.

Scotty,

You have a PM.

Mike

Scotty,

You have a PM.

Mike

No message received yet???



8)
.
.
.
.

Scotty,

Sorry about the pm. I can not find it.

My question was about using BT heads with the std Ford exhaust location since you can get 80cc chamber. Then I could use all parts when installing the BT like the Eds. Of the two heads and considering my present build and future HP goals which would you use? The 545 has the normal 4.390 bore and 4.5 stroke. I would have the BT or Eds ported to stage 3 which includes chamber mods, full exhaust port and some intake work.

Thank you for your help.

Mike

Scotty,

Sorry about the pm. I can not find it.

My question was about using BT heads with the std Ford exhaust location since you can get 80cc chamber. Then I could use all parts when installing the BT like the Eds. Of the two heads and considering my present build and future HP goals which would you use? The 545 has the normal 4.390 bore and 4.5 stroke. I would have the BT or Eds ported to stage 3 which includes chamber mods, full exhaust port and some intake work.

Thank you for your help.

Mike


Mike,

Shoot me an email or telephone me.

The BT's would be a better choice but might be harder to find. The Edelbrocks are allright especially when ported but are not as good as the B/T stuff.



8)

ttt




8)

I've decided to go with a pair for my new build. I'll be placing the order when the time gets nearer. Thanks, Roy

I've decided to go with a pair for my new build. I'll be placing the order when the time gets nearer. Thanks, Roy


Just let me know what and when Roy...

Thanxxx.




8)

I think im going to win the Lottery in a few days. I will let you know. TTT

I think im going to win the Lottery in a few days. I will let you know. TTT



:D




.

TTT

My tentative next project is a 514/521 that I am putting in a '73 MACH I. This is a strictly street (albeit VERY, VERY strong) motor that will run on 93 octane.

I will be using a D0VE block with EAGLE bushed 6.605 rods coupled with J&E forged pistons and a forged stroker crank (TBD). I am looking at a compression ratio of around 10:1 with the 72cc heads while allowing for "growth" and ensuring longevity and reliability - - I may decide to throw spray at the motor sometime in the future.

The question is how much would a "full" porting of the TFS heads add to the base price?

Thanks.

BT

TTT

My tentative next project is a 514/521 that I am putting in a '73 MACH I. This is a strictly street (albeit VERY, VERY strong) motor that will run on 93 octane.

I will be using a D0VE block with EAGLE bushed 6.605 rods coupled with J&E forged pistons and a forged stroker crank (TBD). I am looking at a compression ratio of around 10:1 with the 72cc heads while allowing for "growth" and ensuring longevity and reliability - - I may decide to throw spray at the motor sometime in the future.

The question is how much would a "full" porting of the TFS heads add to the base price?

Thanks.

BT


All of the TFS streets I sell are fully ported.

Cost varies depending on which brand of valves and which spring package the client requires.

Shoot me an email detailing which cam and intake you want to use along with whether or not you want ferrea valves or a mid level S/S valve line to save on costs.

Fully ported with a victor match these castings will support 800 HP with a good solid roller cam.




8)

Have hired help to rough cylinder heads due to the increased volume resulting from the EMC article.


Thanxxx for looking

What is the lead time for somthing with a compettion port job and how much to ship to 19106 in PA?

What is the lead time for somthing with a compettion port job and how much to ship to 19106 in PA?

We are getting lead times to about 30 days on the TFS streets., mabey less depending on how backed up we are at the time of the order. Still clearing the backlog.

Shipping is about $55.00 to $60.00

Thanxxx for looking.



8)

Scotty just talked to you on the phone....Thanks for all the info and letting me pick your brain....I will be calling you back and ordering these heads and cam for my car....Paul

Scotty just talked to you on the phone....Thanks for all the info and letting me pick your brain....I will be calling you back and ordering these heads and cam for my car....Paul

Thank you for checking in with us Paul.

We look forward to taking care of ya.

Just let us know what and when...




8)

8)

n/m

Iguess those p-51s are $#!@ well too lat ill keep the TFSs

Iguess those p-51s are $#!@ well too lat ill keep the TFSs


Huh???



8)

n/m


8)

n/m

ttt

n/m

n/m

Would these heads be good for a 435 cid Nitrous motor? What cam would I use?

The car would be a 2870-2900lb with me,fuel,roll cage,and "Bottles".

With 12:1 CR would it be possible to make 571-632 hp off the "Bottle"

Expected usage is 60% Street/Show,40% Drag.

Thanks.

n/m

8)

n/m

n/m



8)

n/m

Hey Scotty how much are you selling the P-51's for?

Hey Scotty how much are you selling the P-51's for?


They are right in line with the cost Jon Kaase is charging.




8)

8)

you have a pm

ttt

you have a pm

ttt

noted and answered...




8)