460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 17 of 17
Search took 0.01 seconds.
Search: Posts Made By: mdross1
Forum: General Tech 11-24-2013, 07:50 AM
Replies: 12
Views: 954
Posted By mdross1
Recently finished a 427" sbc SB2 engine for a...

Recently finished a 427" sbc SB2 engine for a motorcycle because of wanting to run valve covers without breathers have no choice. During the build and asking around most that run strokers use normal...
Forum: Engine Tech 11-20-2013, 06:48 AM
Replies: 27
Views: 1,767
Posted By mdross1
I'm listening when it comes to SR or FT. Bottom...

I'm listening when it comes to SR or FT. Bottom line is more grunt,years ago the only way was a roller cam.

Heads- Aluminum MotorSports M-6049-A429
Flywheel- Webber Aluminum
Trans- Tremec TKO...
Forum: Engine Tech 11-18-2013, 07:36 AM
Replies: 27
Views: 1,767
Posted By mdross1
Appreciate the posts,my engine cr 10.1,Lunati cam...

Appreciate the posts,my engine cr 10.1,Lunati cam .235 @ .050..560 lift both sides. Edelbrock Performer RPM all port matched. This combo works great just want more. Thought about bigger cubes but...
Forum: Engine Tech 11-17-2013, 06:57 AM
Replies: 27
Views: 1,767
Posted By mdross1
flat tappet to roller tappet cam swap

Been wanting to do a cam change from flat tappet to roller tappet in our Cobra. Thinking about going solids in the aluminum head, 1000cfm dbl pmp, 460. Was hoping to hear from any of you that has...
Forum: Engine Tech 08-12-2013, 07:16 AM
Replies: 13
Views: 1,130
Posted By mdross1
No doubt there are a lot of ways to step up the...

No doubt there are a lot of ways to step up the power level in the rpm bands I use the most.Today with traffic like it is have to be real careful so most spirited driving is down out in the farm...
Forum: Engine Tech 08-02-2013, 06:33 AM
Replies: 13
Views: 1,130
Posted By mdross1
I'll bet it feels plenty strong.My car has a...

I'll bet it feels plenty strong.My car has a 48/52 front/rear weight bias with scaled suspension so it hooks quite well playing with the throttle and using 10.5" drag radials.Forget the BFG's 295...
Forum: Engine Tech 08-01-2013, 07:00 AM
Replies: 13
Views: 1,130
Posted By mdross1
This car does haul the mail it's a kit Cobra just...

This car does haul the mail it's a kit Cobra just had a 1000cfm dbl pmp built on a Perf RPM through aluminum Motorsport heads,Lunati hyd flat tappet .560/.560 @235,Tubular Auto comp headers.Tremec...
Forum: Engine Tech 07-29-2013, 07:35 AM
Replies: 13
Views: 1,130
Posted By mdross1
460 to 514 or bigger

Was wondering has anyone gone from 460 to 514 or bigger and how much more was seat of the pants feel.Since I have a spare 460 and before I decide to change out the flat tappet hydraulic cam to a...
Forum: General Tech 09-13-2012, 05:10 AM
Replies: 10
Views: 1,012
Posted By mdross1
What are the chances you will let us in on the...

What are the chances you will let us in on the secret tractor additive.Been getting ours from John Deere dealer
Forum: Engine Tech 06-14-2012, 05:15 AM
Replies: 6
Views: 723
Posted By mdross1
Without looking over your shoulder sounds like...

Without looking over your shoulder sounds like maybe your burrs are too brittle.Maybe try a HSS.I have always used air die grinders and never restrict the air,never broken any burrs,also never used...
Forum: General Tech 05-13-2012, 05:03 AM
Replies: 10
Views: 1,221
Posted By mdross1
Ran a completely rebuilt small input/output...

Ran a completely rebuilt small input/output Toploader behind the 460 in a Cobra for a few years before upgrading to a TKO.Was never concerned about hurting trans the cast iron case was more than up...
Forum: Engine Tech 04-29-2012, 06:01 PM
Replies: 15
Views: 852
Posted By mdross1
All the above, check your fuel pressure...

All the above, check your fuel pressure first,same time fuel level(assuming you have a Holley) Had one of our gravity feed tractors with floats set wrong make a mess of things luckly we caught it...
Forum: General Tech 04-18-2012, 03:20 PM
Replies: 10
Views: 3,124
Posted By mdross1
Actually for years wanted to stick a 460 in a 67...

Actually for years wanted to stick a 460 in a 67 Fairlane.Always liked the looks of that car.
Forum: Engine Tech 04-15-2012, 05:47 PM
Replies: 4
Views: 783
Posted By mdross1
Building a Donovan sbc with SB2 topend,this block...

Building a Donovan sbc with SB2 topend,this block comes with head and main studs and all the plugs.It could have been run leaving decks alone,the main and cam journals come ready to go.Still needed...
Forum: General Tech 04-15-2012, 04:57 PM
Replies: 10
Views: 3,124
Posted By mdross1
Neat little car can only imagine what that thing...

Neat little car can only imagine what that thing must go like with a 460 nestled under the hood.The girl I married in 69 was always riding around in a Falcon Sprint convertable with a 260 (memory not...
Forum: Jon Kaase Racing Engines 04-10-2012, 05:10 AM
Replies: 5
Views: 2,910
Posted By mdross1
If these heads were available when building my...

If these heads were available when building my 460 would have had a set on my block.
Forum: Engine Tech 04-10-2012, 05:02 AM
Replies: 55
Views: 4,665
Posted By mdross1
Thankfully we that run 500/600hp motors do not...

Thankfully we that run 500/600hp motors do not have to worry about this stuff ha ha,and i personally am anal about fitment.Always use studs my reason is it is easier on the threads.Cast iron like...
Showing results 1 to 17 of 17

 
Forum Jump

All times are GMT -5. The time now is 07:21 PM.



Powered by vBulletin® Copyright ©2000 - 2014, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.