460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 25 of 500
Search took 0.09 seconds.
Search: Posts Made By: D Pope
Forum: Engine Tech 02-13-2015, 11:38 PM
Replies: 37
Views: 1,815
Posted By D Pope
On my block the deck height varied by about 40...

On my block the deck height varied by about 40 thousandths between cylinders. You can't just measure one. I used Probe forged pistons.
Forum: Engine Tech 02-11-2015, 03:35 PM
Replies: 37
Views: 1,815
Posted By D Pope
In my opinion, it would be silly to put in new...

In my opinion, it would be silly to put in new pistons without a rebore and decking the block.
Forum: Engine Tech 02-09-2015, 11:26 PM
Replies: 37
Views: 1,815
Posted By D Pope
Decking the block lets you get away with higher...

Decking the block lets you get away with higher compression without pinging. The squish area is what does it. You don't just deck it x # of thousandths. You measure things and deck it to x inches...
Forum: Car Buildup Forum 02-06-2015, 08:44 PM
Replies: 146
Views: 28,860
Posted By D Pope
It seems like forever since I last worked on the...

It seems like forever since I last worked on the Merc. My daughter bought a fixer-upper house and I've been doing a lot of fixer-upping!
I got new side glass and windshield out of Oregon for a good...
Forum: Engine Tech 02-04-2015, 12:02 AM
Replies: 12
Views: 339
Posted By D Pope
Pull the spark plugs and see what happens.

Pull the spark plugs and see what happens.
Forum: Engine Tech 01-19-2015, 08:23 PM
Replies: 20
Views: 1,062
Posted By D Pope
That piston will need to be changed. I've had...

That piston will need to be changed. I've had that happen before and the piston broke after about 10000 miles.
Forum: Engine Tech 12-31-2014, 04:17 PM
Replies: 30
Views: 815
Posted By D Pope
That'll be a head gasket or a cracked head.

That'll be a head gasket or a cracked head.
Forum: Driveline 12-27-2014, 11:37 PM
Replies: 5
Views: 558
Posted By D Pope
If you have a 390 flywheel the bolt pattern is...

If you have a 390 flywheel the bolt pattern is different and you need a 390 clutch. That's what I have.
Forum: 4x4's, Pullers, Crawlers and other HD rides 12-19-2014, 08:20 PM
Replies: 8
Views: 980
Posted By D Pope
That 208 box looks about tough enough to drive a...

That 208 box looks about tough enough to drive a wringer washing machine.
Forum: Jon Kaase Racing Engines 11-18-2014, 09:40 PM
Replies: 17
Views: 2,231
Posted By D Pope
I've always found that you're better off with no...

I've always found that you're better off with no gaskets. They can't burn out that way!
Forum: Engine Tech 08-20-2014, 01:12 PM
Replies: 14
Views: 470
Posted By D Pope
You'd need to know the vehicles weight and drag...

You'd need to know the vehicles weight and drag coefficient plus gear ratios, tire size, air pressure,etc. What altitude are you at, barometric pressure, wind direction and speed, type of driving and...
Forum: Engine Tech 08-20-2014, 09:30 AM
Replies: 14
Views: 470
Posted By D Pope
Fill the tank and record the mileage. Drive a...

Fill the tank and record the mileage. Drive a bunch then fill again and record the mileage. Miles traveled divided by gallons used equals miles per gallon.
Forum: Engine Tech 08-18-2014, 07:26 PM
Replies: 22
Views: 1,535
Posted By D Pope
Hey guys, 20W-50 isn't thick. If it was straight...

Hey guys, 20W-50 isn't thick. If it was straight 50, maybe!
Forum: Engine Tech 08-14-2014, 11:12 PM
Replies: 7
Views: 648
Posted By D Pope
If your motor's upside down, plastigauge will...

If your motor's upside down, plastigauge will give a pretty close reading on the mains. It it's the right way up, the weight of the crank is resting on the bottom bearings and the clearance is...
Forum: Engine Tech 08-14-2014, 10:56 PM
Replies: 1
Views: 254
Posted By D Pope
If it didn't boil dry it likely won't hurt it. An...

If it didn't boil dry it likely won't hurt it. An engine that has been seriously overheated will start to smoke out the exhaust because the heat wrecks the rings.
Forum: 4x4's, Pullers, Crawlers and other HD rides 04-28-2014, 12:38 AM
Replies: 7
Views: 1,046
Posted By D Pope
The pinion shaft should be parallel with the...

The pinion shaft should be parallel with the tranny output shaft.
Forum: Engine Tech 04-23-2014, 07:54 PM
Replies: 19
Views: 1,030
Posted By D Pope
Probably sludge from the year old fuel got in the...

Probably sludge from the year old fuel got in the needle ans seat and the carb was just overflowing.
Forum: Engine Tech 04-16-2014, 11:08 PM
Replies: 4
Views: 260
Posted By D Pope
Do you have a return line? Deadheading can...

Do you have a return line? Deadheading can increase noise
Forum: Engine Tech 04-15-2014, 02:38 AM
Replies: 15
Views: 1,001
Posted By D Pope
I figured if the 6214 came on the early race...

I figured if the 6214 came on the early race hemis they must be worth something so I checked on eBay. I'll have to take good care of it I guess
Forum: 4x4's, Pullers, Crawlers and other HD rides 04-14-2014, 10:37 PM
Replies: 18
Views: 1,414
Posted By D Pope
Springs are half the battle in a truck pull. If...

Springs are half the battle in a truck pull. If you keep the back end from squatting under load then you're pulling weight off the sled and making it easier to pull!
Forum: Engine Tech 04-14-2014, 09:21 PM
Replies: 15
Views: 1,001
Posted By D Pope
I checked out the 6214 throttle opening and it...

I checked out the 6214 throttle opening and it has linkage issues which is why the primaries open sooner than the secondaries. It is a 1 to 1 ratio linkage.
I only paid $39 for it so I can nail it...
Forum: Engine Tech 04-14-2014, 06:12 PM
Replies: 15
Views: 1,001
Posted By D Pope
The "normal" carb has these #s stamped in: ...

The "normal" carb has these #s stamped in:

12R-9027B

L-7320
3012

The extended carb has these #s:

J
Forum: Engine Tech 04-13-2014, 09:02 PM
Replies: 15
Views: 1,001
Posted By D Pope
I probably won't rev it over about 6000 anyway so...

I probably won't rev it over about 6000 anyway so the one with the extensions might be a good choice. I might run out of hood clearance though.
I'll likely try the 3 barrel first anyway.
Rob, I'm...
Forum: Engine Tech 04-13-2014, 10:57 AM
Replies: 16
Views: 938
Posted By D Pope
With the gas line close to the headers you'll...

With the gas line close to the headers you'll have all kind of vapour lock problems with a dead head system and the pump won't work very long at all.
Put the pump back at the tank and run a half...
Forum: Engine Tech 04-12-2014, 10:50 AM
Replies: 15
Views: 1,001
Posted By D Pope
Dominator question

I have a couple of Dominators and am wondering about the differences. One has those throttle bore extensions that are obviously there to straighten out the air flow through the carb and has about 2...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 12:33 PM.



Powered by vBulletin® Copyright ©2000 - 2015, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.