460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 25 of 109
Search took 0.02 seconds.
Search: Posts Made By: supervel45
Forum: Engine Build Archive 03-11-2014, 10:38 PM
Replies: 9
Views: 3,682
Posted By supervel45
Very nice. What is the initial timing set at? It...

Very nice. What is the initial timing set at? It does not sound much different than my Isky 270 in a 429, st at 14 degree's after it's warmed up.
Forum: Engine Build Archive 03-10-2014, 10:20 AM
Replies: 9
Views: 3,682
Posted By supervel45
http://www.mustangtek.com/Camshaft/camshaft.html ...

http://www.mustangtek.com/Camshaft/camshaft.html I bet the Elgin is close to the old 1972 PI cam, except the Elgin a single pattern. I think both should have good...
Forum: Engine Build Archive 03-10-2014, 08:15 AM
Replies: 2
Views: 1,104
Posted By supervel45
http://www.compcams.com/Company/CC/cam-specs/Detai...

http://www.compcams.com/Company/CC/cam-specs/Details.aspx?csid=1490&sb=2 I am not a big fan of Comp's thumper series cams, but this one is interesting. I bet it makes good low end with the 107 LS,...
Forum: Engine Build Archive 03-10-2014, 07:58 AM
Replies: 9
Views: 3,682
Posted By supervel45
I to have a Comp 4x4 X270 cam I bought off...

I to have a Comp 4x4 X270 cam I bought off Colorado Ford man here, that I am going to try in my 429. You will not get near 18" of Vacuum with these cams. 10"-14" is more likely. I don't think you...
Forum: Chilly's Garage 03-10-2014, 07:33 AM
Replies: 34
Views: 3,600
Posted By supervel45
I agree with keeping the fast cars on the track....

I agree with keeping the fast cars on the track. I doubt any of us would be into cars either, or making money off of Hot Rods if it were not for street racing. As for a the track being safe, the only...
Forum: Chilly's Garage 03-10-2014, 06:22 AM
Replies: 15
Views: 1,153
Posted By supervel45
I would look for a 1972-73 engine. The old...

I would look for a 1972-73 engine. The old 1968-71 engines where closed chamber high compression, and will not be nitrous friendly on pump gas, and even with out nitrous you will need at least 93...
Forum: Chilly's Garage 03-10-2014, 06:01 AM
Replies: 75
Views: 9,699
Posted By supervel45
Cool This old thread is pretty good. Did anyone else...

This old thread is pretty good. Did anyone else notice the long Hemi rod engine had aluminum rods? This may have helped it make it run better also, if he was using steel rods before? As for as the...
Forum: Chilly's Garage 03-10-2014, 04:51 AM
Replies: 3
Views: 485
Posted By supervel45
Cool Traction Loc unlikely. I would not worry about...

Traction Loc unlikely. I would not worry about the D2 heads, set the timing properly, and with our new alky blend gas you will be OK. The roof rust is something to look out for though. And yes the...
Forum: Chilly's Garage 03-10-2014, 04:30 AM
Replies: 1
Views: 246
Posted By supervel45
Cool About 4000 RPM. Nitrious Oxide. Yes they are...

About 4000 RPM. Nitrious Oxide. Yes they are durable. The weak link is the nylon covered timing gear. Would not recomend spaying an orginional 72 chain set.
Forum: Chilly's Garage 12-09-2013, 08:01 PM
Replies: 224
Views: 15,143
Posted By supervel45
Cool double post

double post
Forum: Chilly's Garage 12-09-2013, 07:57 PM
Replies: 224
Views: 15,143
Posted By supervel45
Cool Got you a black varmit rifle, ha ha your hooked....

Got you a black varmit rifle, ha ha your hooked. Wow 143 post's i'm impressed, need a firearms col. Enjoy your new hobby, it is as bad or worse than hot rods.
Forum: Engine Build Archive 09-05-2013, 06:30 AM
Replies: 9
Views: 3,116
Posted By supervel45
I went back and got the ebay #171115100077 on...

I went back and got the ebay #171115100077 on those two 750's converted 3310's, for you. 549 was the starting bid, and no one bid on them, so they might get relisted. I think the guy is a carb....
Forum: The Auction Block 09-05-2013, 05:40 AM
Replies: 10
429
Views: 1,546
Posted By supervel45
Thanks for the reply. Have a good time at the...

Thanks for the reply. Have a good time at the race track too. You should sell it pretty quick at 1800, and If I had the cash to spare I would definetly pick it up.
Forum: The Auction Block 09-05-2013, 05:31 AM
Replies: 10
429
Views: 1,546
Posted By supervel45
Thanks for the reply. Have a good time at the...

Thanks for the reply. Have a good time at the race track too. You should sell it pretty quick at 1800, and If I had the cash to spare I would definetly pick it up.
Forum: Engine Build Archive 09-05-2013, 05:07 AM
Replies: 9
Views: 3,116
Posted By supervel45
Those old 660's used to be quite popular, pretty...

Those old 660's used to be quite popular, pretty cool how all 8 barrels open at the same time, and I saw a pair of 850 center squirts go on ebay for around 500 dollars, I did not even know they made...
Forum: Engine Tech 09-05-2013, 04:16 AM
Replies: 15
Views: 1,063
Posted By supervel45
I would skip the girdle if I was on a budget,...

I would skip the girdle if I was on a budget, don't need it for lower rpm's. The roller rocker's won't gain much on a 268 cam either. The RPM AirGap is a little big for the 268 cam, but not by much,...
Forum: The Auction Block 09-04-2013, 03:36 AM
Replies: 10
429
Views: 1,546
Posted By supervel45
I assume it is a two bolt block. Sounds like a...

I assume it is a two bolt block. Sounds like a very nice engine. How far away are you from Westplains Mo.?
Forum: The Auction Block 09-04-2013, 03:29 AM
Replies: 8
Views: 1,077
Posted By supervel45
Do you still have any of the parts left?

Do you still have any of the parts left?
Forum: Chilly's Garage 09-04-2013, 03:16 AM
Replies: 3
Views: 554
Posted By supervel45
Might want to wrap them with the header heat...

Might want to wrap them with the header heat insulation too. The ones on my 6-71 engine ran hotter than my N/A engine.
Forum: Chilly's Garage 09-04-2013, 03:08 AM
Replies: 14
Views: 1,670
Posted By supervel45
Saw a 1929 Chevy truck at the track once with a...

Saw a 1929 Chevy truck at the track once with a built up strait 6 with two 390cfm holleys and nitrous. I was shocked when he busted off a 6.50 ET in the 1/8 mile, pulling the wheels a little on the...
Forum: Engine Build Archive 09-04-2013, 02:53 AM
Replies: 55
Views: 11,551
Posted By supervel45
+2 If Ford made the 429CJ/SCJ and 3514V...

+2

If Ford made the 429CJ/SCJ and 3514V longer I think you would see them dominating the racetracks. The Clevelands where made in Austraila into the 1980's and seem to still be very popular there,...
Forum: Engine Build Archive 09-04-2013, 01:39 AM
Replies: 3
Views: 1,089
Posted By supervel45
Maybe it's just me, but why do people keep asking...

Maybe it's just me, but why do people keep asking for HP estimates, without camshaft specs., much less head flow numbers if they are worked over? Not gripping at you in paticiular, you are just one...
Forum: Engine Build Archive 09-04-2013, 01:03 AM
Replies: 9
Views: 3,116
Posted By supervel45
This is just an off the cuff estimate, and I...

This is just an off the cuff estimate, and I believe it to be a conserative one. Over 600HP, 550tq. Like I said I feel this is a very conservative estimate, don't even like estimating this stuff,...
Forum: Engine Build Archive 09-04-2013, 12:49 AM
Replies: 37
Views: 6,226
Posted By supervel45
It was all ready a was a low reving torgue...

It was all ready a was a low reving torgue monster, rated at 500ft/lbs I believe in 68-70. If you want more torgue, this is a rare instance, where I would even recomend a stroker kit, LoL. I wish...
Forum: Engine Tech 09-04-2013, 12:09 AM
Replies: 4
Views: 432
Posted By supervel45
What is the duration at .050"? I have looked at...

What is the duration at .050"? I have looked at the Lunati cams for these engines, and I bet the one you listed is 214I, 224E or close to it. It is almost a direct copy of the old Ford SVO 351C,M,400...
Showing results 1 to 25 of 109

 
Forum Jump

All times are GMT -5. The time now is 04:10 PM.



Powered by vBulletin® Copyright ©2000 - 2014, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.