460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 25 of 500
Search took 0.76 seconds.
Search: Posts Made By: The Mad Porter
Forum: Engine Tech 09-14-2014, 09:34 PM
Replies: 4
Views: 98
Posted By The Mad Porter
Cool X2. A thermostatic viscous clutch and 7...

X2.

A thermostatic viscous clutch and 7 blade fan with shroud is more than adequate for my 460 powered LTD which is making 550+ HP.

Pusher fans are inefficient and as stated block total airflow...
Forum: Engine Tech 09-14-2014, 06:16 PM
Replies: 3
Views: 103
Posted By The Mad Porter
Cool Air/Fuel (A/F) Ratios of Common Fuels Fuel...

Air/Fuel (A/F) Ratios of Common Fuels

Fuel A/F Lambda (λ)
Pure Gasoline Stoichiometric 14.7 1.000
Pure Gasoline Max Power Rich 12.5 0.8503
Pure Gasoline Max Power Lean 13.23 0.900
E10...
Forum: Engine Tech 09-14-2014, 05:21 PM
Replies: 3
Views: 103
Posted By The Mad Porter
Cool If you are using E10 fuel which will be typical...

If you are using E10 fuel which will be typical all over the country Stoich is 14.15 give or take.

Given the low compression, loose quench, short total timing (due to weight) and weight, I feel...
Forum: Car Buildup Forum 09-13-2014, 05:12 PM
Replies: 350
Views: 64,866
Posted By The Mad Porter
Cool Thank you. There are many engines like this...

Thank you.

There are many engines like this running in cars and trucks. Some we've built and others we sent top end packages for.

The abundant, high velocity air flow and mild cam mantra works...
Forum: Car Buildup Forum 09-13-2014, 02:58 PM
Replies: 350
Views: 64,866
Posted By The Mad Porter
Cool Original Build is as follows: Stock 70K...

Original
Build is as follows:

Stock 70K mile C9VE 460 short block std bore, factory rods, factory 11 cc dished pistons .002" out of the bore. Re ringed, fresh hone, bearings, paul kane std oil...
Forum: The Auction Block 09-13-2014, 01:06 PM
Replies: 0
Views: 66
Posted By The Mad Porter
Cool WANTED TO BUY 31 spline Trak lok...

A good rebuildable unit or new. May consider another type.


Feel free to email, call or text me with what you have.

Contact information is in signature line.



Thanxx for looking.
Forum: Car Buildup Forum 09-12-2014, 03:03 PM
Replies: 350
Views: 64,866
Posted By The Mad Porter
Cool Thank you to everyone who commented and followed...

Thank you to everyone who commented and followed this build. It was long and had some hiccups along the way but in the end the results were well worth waiting for. There is certainly an 11.9x pass in...
Forum: The Auction Block 09-11-2014, 11:55 PM
Replies: 2
Views: 195
Posted By The Mad Porter
Cool New ford F3TE's or the aftermarket new...

New ford F3TE's or the aftermarket new replacement heads?


I would be interested.



S
Forum: Engine Tech 09-08-2014, 02:45 PM
Replies: 6
Views: 297
Posted By The Mad Porter
Cool Yes. S

Yes.


S
Forum: Car Buildup Forum 09-06-2014, 10:20 PM
Replies: 350
Views: 64,866
Posted By The Mad Porter
Cool Here is an SAE Net chassis dyno run from last...

Here is an SAE Net chassis dyno run from last Friday:

456.5 RWHP @ 6,200 rpm
449.09 TQ

Remember the cam is 224 center 4 /228 corners /234 110/112 Three pattern juice roller with solid...
Forum: Car Buildup Forum 09-06-2014, 05:19 PM
Replies: 350
Views: 64,866
Posted By The Mad Porter
Cool Will do later today. S

Will do later today.


S
Forum: Car Buildup Forum 09-06-2014, 05:16 PM
Replies: 350
Views: 64,866
Posted By The Mad Porter
Cool Thank you Nick. It was a pleasure meeting you and...

Thank you Nick. It was a pleasure meeting you and your wife. :)


You tube link to a run.

http://youtu.be/nuPBMCmqz4s

Same run from inside car. 12.33 @ 109.39:

...
Forum: Car Buildup Forum 09-06-2014, 05:01 PM
Replies: 350
Views: 64,866
Posted By The Mad Porter
Cool Thank you. There is an 11.99 there. DA was 2063"...

Thank you. There is an 11.99 there. DA was 2063" and it was in the 80's


3.50 27.7" tall 295 55 15 MT ET Drag radial.

11" 3450 stall convertor.
Forum: Car Buildup Forum 09-06-2014, 04:54 PM
Replies: 350
Views: 64,866
Posted By The Mad Porter
12.04 @ 113.42 MPH Best Pass.

Finally got old girl to dead hook at WOT in the left lane. :D:D:D

Best time shifting at 6500 rpm.

4,460 pound racing weight.




Vid of second best run:
Forum: Engine Tech 09-05-2014, 07:46 PM
Replies: 13
Views: 494
Posted By The Mad Porter
Cool EFI 3Y crank counter weights are smaller. ...

EFI 3Y crank counter weights are smaller.

You will have to cut down the early crank counter weights and or clearance to bottoms of the cylinders and then rebalance.


S
Forum: Engine Tech 09-04-2014, 08:12 PM
Replies: 13
Views: 494
Posted By The Mad Porter
Cool The internal balance crankshafts have slightly...

The internal balance crankshafts have slightly larger counter weights and will not fit in the later block with its longer cylinders with out modification.

Auto or manual trans?




S
Forum: Engine Tech 09-03-2014, 11:39 PM
Replies: 3
Views: 170
Posted By The Mad Porter
Cool The balast wire is between the coil pos and...

The balast wire is between the coil pos and firewall connector.

If you are replacing the coil with a point ignition use a coil designed for a ballasted point ignition system.

If you have...
Forum: Engine Tech 09-03-2014, 09:48 PM
Replies: 3
Views: 170
Posted By The Mad Porter
Cool What year vehicle is the 70 460 in? ...

What year vehicle is the 70 460 in?



All point triggered vehicles have the ballast in the ignition positive wire to the coil.



S
Forum: Engine Tech 09-03-2014, 09:44 PM
Replies: 16
Views: 673
Posted By The Mad Porter
Cool Pump bypass stuck open or partially open... ...

Pump bypass stuck open or partially open...


S
Forum: Engine Tech 09-02-2014, 01:30 AM
Replies: 3
Views: 210
Posted By The Mad Porter
Cool Sounds like you have too much vacuum advance. ...

Sounds like you have too much vacuum advance.

The duraspark distributors have an adjustable dashpot. 1/8" allen CCW to slow the advance and limit travel. First check to see how much you have...
Forum: Engine Tech 09-01-2014, 02:45 PM
Replies: 11
Views: 443
Posted By The Mad Porter
Cool According to my research and talks with Stan who...

According to my research and talks with Stan who has been doing this for forever (1962) the H should be the same diameter as the pipe you are using.

I like both the X and the H but for different...
Forum: Engine Tech 09-01-2014, 01:23 AM
Replies: 11
Views: 443
Posted By The Mad Porter
Cool Thanxx Steve. Stan's does great work. I...

Thanxx Steve. Stan's does great work.

I agree and have had to go that route before.



S
Forum: Engine Tech 08-31-2014, 09:34 PM
Replies: 10
Views: 358
Posted By The Mad Porter
Cool I just installed that oil pan kit on a client...

I just installed that oil pan kit on a client build and it is indeed 9.5" deep. Nice kit for the price though it is just a stock un-baffled truck pan.

6 quarts put it half way from add to full...
Forum: Engine Tech 08-31-2014, 09:05 PM
Replies: 11
Views: 443
Posted By The Mad Porter
Cool X2... When I started my 460" LTD project...

X2...


When I started my 460" LTD project I was shooting for 500 HP so I did my exhaust in 2.5" utilizing a summit mandrel X pipe kit, walker dynomax ultras and my crush bent 2.5" tail pipes.
...
Forum: Engine Tech 08-31-2014, 08:26 PM
Replies: 26
Views: 2,696
Posted By The Mad Porter
Cool I am using the MSD 6AL2 and blaster coil on my...

I am using the MSD 6AL2 and blaster coil on my LTD with a custom curved duraspark distributor.

Runs flawlessly to the 6500 rpm shift point.

Though I like the MSD distributors the BBF unit is...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 04:35 AM.



Powered by vBulletin® Copyright ©2000 - 2014, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.