460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 25 of 500
Search took 0.65 seconds.
Search: Posts Made By: The Mad Porter
Forum: Engine Tech 10-24-2014, 10:32 PM
Replies: 31
Views: 1,027
Posted By The Mad Porter
Cool Given the primary use at 4000 feet you are...

Given the primary use at 4000 feet you are leaving efficiency on the table by not tightening quench and raising static c/r. The occasional jaunt to sea level can easily be dealt with by using 89...
Forum: Engine Tech 10-22-2014, 10:06 PM
Replies: 3
514
Views: 177
Posted By The Mad Porter
Cool Given the same cylinder heads about 400 rpm. ...

Given the same cylinder heads about 400 rpm.

How well the combo performs will depend on which heads you settle on.

Heavily ported large valve PC heads are little better than passenger car...
Forum: Engine Tech 10-21-2014, 10:20 PM
Replies: 5
Views: 275
Posted By The Mad Porter
Cool An iron headed BBF will typically need no less...

An iron headed BBF will typically need no less than 34 to 36 degrees total timing. Initial plus mechanical. Under certain circumstances they might want more. At what RPM you allow total advance will...
Forum: Engine Tech 10-21-2014, 01:15 PM
Replies: 5
Views: 188
Posted By The Mad Porter
Cool Which space you will use depends on how your...

Which space you will use depends on how your stroker rotating assembly was balanced.

For internal use the sleeve.

For external use the hatchet.



S
Forum: Engine Tech 10-19-2014, 06:16 PM
Replies: 3
Views: 125
Posted By The Mad Porter
Cool Order the fuel pressure for a 95 mustang GT from...

Order the fuel pressure for a 95 mustang GT from BBK and you will have what you need.



S
Forum: Engine Tech 10-19-2014, 06:15 PM
Replies: 3
Views: 160
Posted By The Mad Porter
Cool X2. That cam has too much duration. ...

X2.

That cam has too much duration.




S
Forum: Engine Tech 10-19-2014, 02:50 PM
Replies: 9
Views: 287
Posted By The Mad Porter
Cool Have the T2 runner exits been port matched??? ...

Have the T2 runner exits been port matched???



S
Forum: Engine Tech 10-17-2014, 10:10 PM
Replies: 7
Views: 314
Posted By The Mad Porter
Cool Yes. Follow their instructions to the letter. ...

Yes. Follow their instructions to the letter.

There is an accumulator groove between the first and second ring to help address any potential ring flutter.


The United engine and machine site...
Forum: Engine Tech 10-17-2014, 04:13 PM
Replies: 7
Views: 340
Posted By The Mad Porter
Cool X2... If you want the upgrade to the felpro...

X2...

If you want the upgrade to the felpro 1018 get the ford motorsports gaskets from lem.



S
Forum: Engine Tech 10-16-2014, 12:18 PM
Replies: 17
Views: 629
Posted By The Mad Porter
It is the same reason some yahoos blast the base...

It is the same reason some yahoos blast the base in his/her stereo at a stop light... Attention. :mad:


I hold the LTD at 4K for a moment then thrash it to make the exhaust rap. Amazing how the...
Forum: Engine Tech 10-13-2014, 04:51 PM
Replies: 10
Views: 453
Posted By The Mad Porter
Cool All 460's are flat tappet cammed. You must...

All 460's are flat tappet cammed.

You must be referring to a late truck EFI engine???


What are your intended cam specs?

If duration is under 230 ish intake you will likely not need to...
Forum: The Auction Block 10-13-2014, 04:05 PM
Replies: 4
Views: 930
Posted By The Mad Porter
Cool SCJ-B's arrived safely and as pictured. ...

SCJ-B's arrived safely and as pictured.

Thanxx Matt.




S
Forum: Engine Tech 10-11-2014, 09:42 PM
Replies: 22
Views: 935
Posted By The Mad Porter
Cool This is absolutely true and applicable...

This is absolutely true and applicable specifically to the KB pistons. Many KB hyper failures if not most are related to improper top ring gap.

Secondary is detonation.

We have used KB hypers...
Forum: Engine Tech 10-11-2014, 05:07 PM
Replies: 22
Views: 935
Posted By The Mad Porter
Cool :o Well stated Randy. :) S

:o


Well stated Randy. :)



S
Forum: Engine Tech 10-11-2014, 03:57 PM
Replies: 22
Views: 935
Posted By The Mad Porter
Cool We have successfully utilized all of the hyper...

We have successfully utilized all of the hyper sealed power pistons in budget performance applications.

H418 22 cc dish

H535 flat top with dual intake reliefs

H582 efi pistons with 6 cc dish...
Forum: Engine Tech 10-11-2014, 02:21 PM
Replies: 7
Views: 340
Posted By The Mad Porter
Cool With out question forged pistons. :D What...

With out question forged pistons. :D

What heads are you using???

10 to 1 with boost and E85 is fine.


The higher the intake / exhaust back pressure ratio the wider the LSA needs to be.
Forum: The Auction Block 10-10-2014, 10:23 PM
Replies: 5
Views: 696
Posted By The Mad Porter
Cool All parts have arrived safely, as described and...

All parts have arrived safely, as described and carefully packed.


Thank you Jeff.



S
Forum: The Auction Block 10-08-2014, 12:13 AM
Replies: 6
Views: 480
Posted By The Mad Porter
Cool Shoot me some pics via text would you? ...

Shoot me some pics via text would you?

Number in signature line please.



:D


S
Forum: Engine Tech 10-06-2014, 08:52 PM
Replies: 12
Views: 379
Posted By The Mad Porter
Cool X2 You can restrict the cross over with...

X2


You can restrict the cross over with sheet metal cut to fit and a 5/16" hole to quickly heat the intake but not overheat it.



S
Forum: Engine Tech 10-06-2014, 08:19 PM
Replies: 6
Views: 475
Posted By The Mad Porter
Cool I mocked up a small bore on an SCJ head to check....

I mocked up a small bore on an SCJ head to check.

Intake valve clears small bore, exhaust valve after about .500" lift WILL hit the cylinder unless the bore is notched.

At 370 cubic inches...
Forum: Engine Tech 10-05-2014, 07:09 PM
Replies: 1
Views: 207
Posted By The Mad Porter
Cool In order to accurately answer your question: ...

In order to accurately answer your question:

Vehicle
Weight
Gearing and trans.
Cylinder head type?
Cam specs?
Forum: Engine Tech 10-04-2014, 01:43 PM
Replies: 4
Views: 277
Posted By The Mad Porter
Cool Use the search function. There are multiple...

Use the search function.

There are multiple posts concerning EFI upgrades.
They are listed in order of importance. Search my name and you will find the posts and or replies. :D



S
Forum: The Auction Block 10-02-2014, 08:28 PM
Replies: 4
Views: 930
Posted By The Mad Porter
Cool Funds request paid. Thanxx, S

Funds request paid.


Thanxx,



S
Forum: The Auction Block 10-01-2014, 07:53 PM
Replies: 5
Views: 696
Posted By The Mad Porter
Cool Thanks for the prompt attention jeff. S

Thanks for the prompt attention jeff.



S
Forum: The Auction Block 10-01-2014, 04:01 PM
Replies: 5
Views: 696
Posted By The Mad Porter
Cool PM sent. S

PM sent.


S
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 01:13 AM.



Powered by vBulletin® Copyright ©2000 - 2014, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.