460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 25 of 500
Search took 0.09 seconds.
Search: Posts Made By: butterbean
Forum: Chilly's Garage 08-27-2015, 03:27 PM
Replies: 1
Views: 12
Posted By butterbean
FREE MONEY

Hello everybody, if you have ate starkist tuna from 2009-2014 the 5 oz cans size, they have settled a class action law suit and is giving away 25.00 in cash or 50.00 in tuna, just go to...
Forum: Engine Tech 08-27-2015, 10:50 AM
Replies: 10
Views: 422
Posted By butterbean
well more than likely the cam tunnel has been...

well more than likely the cam tunnel has been line bored due to spun cam bearings, I too would be weary about the block, the only way to tell is take it to a machine shop with both cams and tell them...
Forum: Engine Tech 08-24-2015, 04:54 PM
Replies: 3
Views: 323
Posted By butterbean
67cougar is rite about 200-250 is the going rate...

67cougar is rite about 200-250 is the going rate for a rebuildable short block
Forum: Car Buildup Forum 08-24-2015, 08:41 AM
Replies: 218
Views: 24,131
Posted By butterbean
car looks clean and straight, the pass was real...

car looks clean and straight, the pass was real smooth and looked good, there is nothing wrong with the NOS converter it just needs a 100-150 to get it going, I know 144 MPH is a low 9.20's pass,...
Forum: Chilly's Garage 08-22-2015, 02:20 PM
Replies: 1
Views: 211
Posted By butterbean
Cale

any updates on Cale Aronson, have not herd or seen anything in a while
Forum: Engine Tech 08-22-2015, 11:39 AM
Replies: 10
Views: 687
Posted By butterbean
looks like oil to me, maybe a guide leaking or...

looks like oil to me, maybe a guide leaking or guide seal??? or the rings???
Forum: Chilly's Garage 08-21-2015, 12:12 PM
Replies: 2
Views: 149
Posted By butterbean
who is

who is Cheyenne Stanley????
Forum: Engine Tech 08-20-2015, 02:34 PM
Replies: 33
Views: 1,765
Posted By butterbean
if you have 2 bent pushrods then you may have 2...

if you have 2 bent pushrods then you may have 2 bent valves in that cyl. hope not but there is a good chance, good luck
Forum: Engine Tech 08-19-2015, 11:06 AM
Replies: 27
Views: 1,507
Posted By butterbean
the answer is YES, and it should have ran 6.80's...

the answer is YES, and it should have ran 6.80's to 6.90's in the 1950 lb digger if the HP was rite!!!
Forum: Engine Tech 08-17-2015, 11:50 AM
Replies: 3
Views: 363
Posted By butterbean
yes dominators are good carbs when tuned rite,...

yes dominators are good carbs when tuned rite, but for street driving you may want to buy a 4150 style carb like a holley 950 HP carb but me personally i like Dommy's
Forum: Engine Build Archive 08-15-2015, 03:54 PM
Replies: 10
Views: 1,217
Posted By butterbean
looks like the going faster bug has bit you hard,...

looks like the going faster bug has bit you hard, good luck and have fun with it
Forum: Engine Tech 08-13-2015, 11:03 AM
Replies: 27
Views: 1,507
Posted By butterbean
there has to be something WRONG with the dyno, I...

there has to be something WRONG with the dyno, I know Snowball's 604 with C-heads makes 1100 HP or close to it with one carb and yours only made 900.3 something is not jiving friend, I know your carb...
Forum: Engine Tech 08-12-2015, 01:53 PM
Replies: 12
Views: 413
Posted By butterbean
piston to valve is at its closest at -10*before...

piston to valve is at its closest at -10*before TDC or +10* after TDC if I remember rite
Forum: Engine Tech 08-12-2015, 11:59 AM
Replies: 31
Views: 1,652
Posted By butterbean
A-MEN brother Randy,

A-MEN brother Randy,
Forum: Engine Tech 08-12-2015, 11:56 AM
Replies: 12
Views: 413
Posted By butterbean
I was always told that .100 is safe on big solid...

I was always told that .100 is safe on big solid rollers, I would be kinda worried if I had only .055 clearance on my engine with a .700 ish lift but thats only my opnion, good luck, and maybe you...
Forum: Engine Tech 08-10-2015, 10:42 PM
Replies: 8
Views: 269
Posted By butterbean
thanks guy's for the info, i'll pass it on

thanks guy's for the info, i'll pass it on
Forum: Engine Tech 08-10-2015, 09:46 PM
Replies: 8
Views: 269
Posted By butterbean
FE question

I know this is not a FE forum but there are a lot of engine builders on here so here it goes, at the machine shop today and the machinist don't know how much he can bore a 1968 390 block safe, its...
Forum: Engine Tech 08-10-2015, 09:39 PM
Replies: 10
Views: 583
Posted By butterbean
well I did not know that so most of our gas...

well I did not know that so most of our gas stations are .10 cents apart so now our gas is 2.49-reg 2.59-med -2.69 for high test and thats 87-89-93, and I thought that a flat top with a D3VE head...
Forum: Engine Tech 08-10-2015, 05:39 PM
Replies: 5
Views: 221
Posted By butterbean
doing good Pete, just got my car going and ready...

doing good Pete, just got my car going and ready for some Bracket action, I will give you a call later tonight
Forum: Engine Tech 08-10-2015, 05:36 PM
Replies: 10
Views: 583
Posted By butterbean
why would you want to run 87 fuel anyway?? you...

why would you want to run 87 fuel anyway?? you know for just a few dollars more per tank you could use 91-93, for .20 cents more a gallon to fill a 20 gallon tank is only 4.00 frigging dollars...
Forum: Engine Tech 08-10-2015, 11:38 AM
Replies: 5
Views: 221
Posted By butterbean
hello Pete how's it been going?? well on mine I...

hello Pete how's it been going?? well on mine I set them .004/.005 tighter than set hot lash and have had no issues, hope this helps
Forum: Engine Tech 08-08-2015, 05:34 PM
Replies: 4
Views: 265
Posted By butterbean
I would just use a single moly top ring and a...

I would just use a single moly top ring and a standard 2nd ring, but I would get file fit rings and set end gap for spray, good luck
Forum: Engine Build Archive 08-07-2015, 09:13 PM
Replies: 40
Views: 8,361
Posted By butterbean
come on Tim, let us know how she's running???

come on Tim, let us know how she's running???
Forum: Engine Build Archive 08-07-2015, 09:12 PM
Replies: 9
Views: 1,827
Posted By butterbean
bump for updates???

bump for updates???
Forum: Engine Build Archive 08-07-2015, 09:09 PM
Replies: 10
Views: 1,217
Posted By butterbean
any updates maggard??

any updates maggard??
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 04:25 PM.



Powered by vBulletin® Copyright ©2000 - 2015, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.