460 Ford Forum - Search Results
Advanced Search
Showing results 1 to 25 of 365
Search took 0.07 seconds.
Search: Posts Made By: stuarta
Forum: Driveline   02-01-2016, 11:46 PM
Replies: 3
Views: 193
Posted By stuarta
Yup.

Yup.
Forum: Driveline   01-29-2016, 12:21 AM
Replies: 4
Views: 820
Posted By stuarta
Install a longer modulator pin.

Install a longer modulator pin.
Forum: Driveline   12-27-2015, 08:57 AM
Replies: 2
Views: 625
Posted By stuarta
C3?

I imagine you mean C6. This is a very strong transmission.
Forum: Driveline   08-31-2015, 05:42 AM
Replies: 13
Views: 1,731
Posted By stuarta
Depends how you beat on them.

Depends how you beat on them.
Forum: Engine Tech   08-25-2015, 09:25 AM
Replies: 14
Views: 629
Posted By stuarta
How much should it have been torqued to?

How much should it have been torqued to?
Forum: Driveline   07-22-2015, 09:45 PM
Replies: 5
Views: 844
Posted By stuarta
Your first mistake was B&M. You will be...

Your first mistake was B&M.


You will be better off getting a different valve body and installing a Transgo kit.
Forum: Driveline   05-08-2015, 01:52 AM
Replies: 2
Views: 656
Posted By stuarta
If the bushing came out the pump housing will be...

If the bushing came out the pump housing will be damaged. Tear it apart.
Forum: Driveline   05-08-2015, 01:50 AM
Replies: 4
Views: 848
Posted By stuarta
Yes. And please flush the cooler and lines.

Yes. And please flush the cooler and lines.
Forum: Driveline   04-01-2015, 08:14 PM
Replies: 4
Views: 633
Posted By stuarta
I answered in a different forum.

I answered in a different forum.
Forum: Driveline   02-16-2015, 10:21 AM
Replies: 8
Views: 1,105
Posted By stuarta
Can you install the cooler on the other side of...

Can you install the cooler on the other side of the rad?
Forum: Driveline   01-05-2015, 06:31 PM
Replies: 7
Views: 1,161
Posted By stuarta
More than one turn is bad. Either the...

More than one turn is bad.

Either the lining is gone or it was never adjusted.

You would be wise to drop the valve body, remove the struts and look at the ends of the band.
Forum: Driveline   01-05-2015, 09:06 AM
Replies: 7
Views: 1,161
Posted By stuarta
How loose is extremely loose? Lining on the...

How loose is extremely loose?

Lining on the band is very thin.

Drop the pan and look for junk.
Forum: The Auction Block   12-10-2014, 10:00 PM
Replies: 2
Views: 429
Posted By stuarta
What engine?

What engine?
Forum: Driveline   11-11-2014, 10:50 AM
Replies: 6
Views: 1,232
Posted By stuarta
By that it sounds like the over run clutch has...

By that it sounds like the over run clutch has had the biscuit.


The only way to correct this is a complete tear down.
Forum: Driveline   11-09-2014, 09:34 AM
Replies: 6
Views: 1,232
Posted By stuarta
Give a few more details. Do you mean if the...

Give a few more details.

Do you mean if the transmission is placed in Low it drives then will shift to 2nd then 3rd if the lever is moved but won't move if starting out in Drive position?
Forum: Driveline   10-17-2014, 09:04 PM
Replies: 14
Views: 1,421
Posted By stuarta
You must remove the transmission and open it up...

You must remove the transmission and open it up to replace the band so may as well look at seals and clutches while in there.
Forum: Driveline   10-17-2014, 02:06 PM
Replies: 14
Views: 1,421
Posted By stuarta
You are living on borrowed time. I hope there is...

You are living on borrowed time. I hope there is a bit of lining left or the drum will be ruined.
Forum: Driveline   10-12-2014, 03:24 PM
Replies: 14
Views: 1,421
Posted By stuarta
Ready for PB&J.

Ready for PB&J.
Forum: Driveline   10-11-2014, 01:06 PM
Replies: 14
Views: 1,421
Posted By stuarta
Check the band adjustment. The screw is in front...

Check the band adjustment. The screw is in front of the lever. Hold the adjuster and loosen the lock nut. Torque the adjuster to 10 foot pounds and back it off 1 1/2 turns. Still holding the adjuster...
Forum: Driveline   10-01-2014, 02:16 PM
Replies: 4
Views: 1,186
Posted By stuarta
A tad snug but should be ok.

A tad snug but should be ok.
Forum: Driveline   09-25-2014, 07:16 AM
Replies: 22
Views: 2,136
Posted By stuarta
Ribs are there for added support. The bell...

Ribs are there for added support. The bell housings are different.

Like Greg mentioned. Lincoln transmissions are good but take some invention for a rear mount.
Forum: Driveline   09-15-2014, 10:44 AM
Replies: 20
Views: 1,724
Posted By stuarta
It is not mandatory that a dial indicator be...

It is not mandatory that a dial indicator be used. Feeler gauges work just as well.
I set 6 clutches @ .090 clearance.

What kind of valve body do you have?
Forum: Driveline   09-13-2014, 12:26 PM
Replies: 4
Views: 852
Posted By stuarta
The dipstick should say what is recommended.

The dipstick should say what is recommended.
Forum: Driveline   09-12-2014, 07:05 PM
Replies: 9
Views: 1,681
Posted By stuarta
10 springs is all that is required. Space them...

10 springs is all that is required. Space them out. As long as they aren't all close together.

The over run race is what holds the snap ring.

Piston, race, spring retainer, snap ring.
Forum: Driveline   09-02-2014, 09:54 PM
Replies: 20
Views: 1,724
Posted By stuarta
You can use a lower forward pressure plate...

You can use a lower forward pressure plate instead of the thicker plate.
Showing results 1 to 25 of 365

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome