460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 25 of 500
Search took 0.29 seconds.
Search: Posts Made By: zephyrbob
Forum: Engine Tech 09-01-2015, 09:28 PM
Replies: 15
Views: 526
Posted By zephyrbob
I have done valve covers breathers and other...

I have done valve covers breathers and other brackets and stuff. I do not recall alum stuff though. so if scott is correct then skip the dishwasher soap and use just the hot water cycle. I did run it...
Forum: Engine Tech 09-01-2015, 07:17 AM
Replies: 15
Views: 526
Posted By zephyrbob
wait for the ball and chain to go shopping with...

wait for the ball and chain to go shopping with her mother. then use the dishwasher that you paid for anyway. use the same **** that she uses for dishes just throw an extra one in there. just saying,...
Forum: Engine Tech 08-07-2015, 06:58 PM
Replies: 8
Views: 382
Posted By zephyrbob
not enough fuel pump for a 302. bob

not enough fuel pump for a 302. bob
Forum: General Tech 08-06-2015, 10:28 PM
Replies: 10
Views: 595
Posted By zephyrbob
Rich, mine ride is a street car. not a expensive...

Rich, mine ride is a street car. not a expensive race car engine. for me the oil pressure switch is to kill the electric fuel pump if I whack the car or stall the engine. hopefully to prevent the...
Forum: General Tech 08-05-2015, 08:26 AM
Replies: 10
Views: 595
Posted By zephyrbob
that's exactly what I did. the over ride switch...

that's exactly what I did. the over ride switch is nice when refilling the float bowls after any carb work. I tied the oil pressure switch in series with the relay.

....make sure you are not...
Forum: Engine Tech 07-30-2015, 10:03 AM
Replies: 22
Views: 1,152
Posted By zephyrbob
some ramblings for you. my fox with alum heads...

some ramblings for you. my fox with alum heads weighs 3270 with me in in it. the motor sits with 6 of the 8 cylinders forward of the spindles. 1950 front axle, 1320 rear.
....I picked the...
Forum: Engine Tech 07-16-2015, 10:53 PM
Replies: 20
Views: 716
Posted By zephyrbob
sounds like it is time to run some jumper wires...

sounds like it is time to run some jumper wires to the box. pull the plug run and temporarly run your wires. google up duraspark ii for a wiring diagram. good luck. bobn

also not being a smart...
Forum: Engine Tech 07-16-2015, 07:48 AM
Replies: 20
Views: 716
Posted By zephyrbob
I have had two interesting problems in the past...

I have had two interesting problems in the past on two different cars that were similar to your problem. the first would run get hot and stall. the alternator had a bad diode and would overheat the...
Forum: Events 06-28-2015, 10:32 PM
Replies: 6
Views: 856
Posted By zephyrbob
home,,,she was there. lol. even willie b was...

home,,,she was there. lol. even willie b was there announcing. you guys can watch it on teebee soon. lol.
....the mighty montego powered by carl looked good inside, outside, under the hood and...
Forum: Events 06-20-2015, 07:57 PM
Replies: 6
Views: 856
Posted By zephyrbob
lets see, new parts are in. receiver hitch on for...

lets see, new parts are in. receiver hitch on for designated tow recovery point, race tires mounted, balanced with steel valve stems, quick release fire extinguisher mounted. road trip, ROAD TRIP....
Forum: Events 06-02-2015, 08:40 PM
Replies: 6
Views: 856
Posted By zephyrbob
my fiesta st is up on the stands . front bumper...

my fiesta st is up on the stands . front bumper cover off. it gets a bigger intercooler, charge pipes, motor mount and new intake. finally a mountune tune.
....zeph is parked till after event lol....
Forum: Events 05-17-2015, 10:01 PM
Replies: 1
Views: 428
Posted By zephyrbob
looks like there are still some spots open for...

looks like there are still some spots open for the Colorado springs event. on Friday night all the cars from the pikes peak hill climb are on display downtown. bobn

ps fear the fiesta st, i'm...
Forum: Engine Tech 04-03-2015, 09:41 PM
Replies: 2
Views: 350
Posted By zephyrbob
there is a ton of room under the hood of that...

there is a ton of room under the hood of that truck to work. a set of craftsman tools for a beginner is approx. 250 and decent torque wrench is aprox 150. a cheap manual is 75. a gasket set 125....
Forum: Car Buildup Forum 12-26-2014, 10:19 PM
Replies: 249
Views: 23,047
Posted By zephyrbob
d and d motorsports out of kali. coilovers from...

d and d motorsports out of kali. coilovers from them too. however mine only had one adjustment nut on the sleeve. bob
Forum: Car Buildup Forum 12-26-2014, 07:39 AM
Replies: 249
Views: 23,047
Posted By zephyrbob
the Lakewood struts on my zeph worked fine with...

the Lakewood struts on my zeph worked fine with the spacers. the problem I had was getting enough ride height out of the spring for the tire to clear the wheel well. 175 14s were coil bound. 250 14s...
Forum: Car Buildup Forum 12-15-2014, 07:52 AM
Replies: 249
Views: 23,047
Posted By zephyrbob
the three things that are different than a stang...

the three things that are different than a stang that affected me the most> rear wheel wells are small. stock size tires were little bitty 14s.
.... gas tank is all the way to one side not centered...
Forum: Car Buildup Forum 10-22-2014, 10:26 PM
Replies: 249
Views: 23,047
Posted By zephyrbob
I found out the hard way that my tubular front...

I found out the hard way that my tubular front end did not include the a arm bolts. after I tossed the stock kmember. go figure, bob
Forum: Engine Tech 08-31-2014, 07:28 PM
Replies: 26
Views: 3,298
Posted By zephyrbob
hmmm, my msd equipt pos starts easier, restarts...

hmmm, my msd equipt pos starts easier, restarts easier when hot, runs better and seems quicker than the famed duraspark. there are no ford duraspark boxes available, just foreign made crapola...
Forum: Chilly's Garage 08-30-2014, 11:13 AM
Replies: 59
Views: 5,441
Posted By zephyrbob
sure, come to minn. don't stay for free in the...

sure, come to minn. don't stay for free in the best walleye/northern fishing area there is. lol j/k too bad you didn't mention it previously. bob

ps google fishbowl of minn/wisc.
Forum: Car Buildup Forum 08-28-2014, 11:11 PM
Replies: 26
Views: 2,944
Posted By zephyrbob
with out the heater box but with alum heads mine...

with out the heater box but with alum heads mine weighs 3270 me in it. nose is heavy 990df 960 pf dr660 pr660. that's with rear seat, battery in stock location, also spare tire in stock location. my...
Forum: Engine Tech 08-02-2014, 06:48 PM
Replies: 27
Views: 1,655
Posted By zephyrbob
kinda sounds like more of a tech school project...

kinda sounds like more of a tech school project than a real deal. the car/truck/boat is the starting point not the motor....bob
Forum: Engine Build Archive 07-29-2014, 09:58 PM
Replies: 31
Views: 10,265
Posted By zephyrbob
for comparison sakes your motor(same cam) as...

for comparison sakes your motor(same cam) as mine. running a 850 on a torker II intake in a 3280 fox body zeph. it is in the 12s with 327 gear. gets 12 to 14 mpg, easily cruises at 70. traction is a...
Forum: Driveline 07-15-2014, 11:28 PM
Replies: 11
Views: 1,085
Posted By zephyrbob
we got you hooked! you are on the way! lol, bobn

we got you hooked! you are on the way! lol, bobn
Forum: Driveline 07-14-2014, 11:41 PM
Replies: 11
Views: 1,085
Posted By zephyrbob
if you are not in hurry take it apart and work on...

if you are not in hurry take it apart and work on it yourself. I ripped apart three trannys to finger it out myself. stu, gregaust and badshoe offer advise on the ford tranny forum. also on this...
Forum: Engine Tech 07-13-2014, 09:56 PM
Replies: 31
Views: 2,312
Posted By zephyrbob
learned the hard way randys' warning is spot...

learned the hard way randys' warning is spot on,,,,,bob
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 06:48 PM.



Powered by vBulletin® Copyright ©2000 - 2015, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.