460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 25 of 500
Search took 0.52 seconds.
Search: Posts Made By: Paul Kane
Forum: Engine Tech 10-22-2014, 10:56 AM
Replies: 7
Views: 200
Posted By Paul Kane
The L2404 Speed Pro weighs damn near 1000g with...

The L2404 Speed Pro weighs damn near 1000g with pin, is a decades-old design, and currently has poor machining consistency.

The Probe FPS 460 piston is of a superior overall design, weighs a...
Forum: Engine Tech 10-21-2014, 07:40 PM
Replies: 31
Views: 876
Posted By Paul Kane
It does not have F because the block was not used...

It does not have F because the block was not used in a CJ Mustang engine.

Z does not desiginate KarKraft because it is not a C9AE Boss block.

Your mix-matching codes and blocks.

Re-read...
Forum: Engine Tech 10-21-2014, 07:18 PM
Replies: 31
Views: 876
Posted By Paul Kane
^Absurd.^ And over thinking it. This kind...

^Absurd.^ And over thinking it.

This kind of thing does happen on production lines, and is known to have gone on at FoMoCo. 4-bolt blocks did indeed end up in passenger car engines; even the...
Forum: Engine Tech 10-21-2014, 07:03 PM
Replies: 31
Views: 876
Posted By Paul Kane
What's The Big Deal?

I don't see what all the hoopla is about, there's no mystery here. It's a normal facotry 4-Bolt passenger car block. Not the first DiVE 4-bolt block I've seen which, in all seriousness, is a D0VE...
Forum: Engine Tech 10-13-2014, 01:00 PM
Replies: 26
Views: 892
Posted By Paul Kane
I have personally known the KB hypers to...

I have personally known the KB hypers to withstand a lot more abuse than the Speed Pro hypers. They also have a better pin location and far better piston-to-piston machining tolerance consistency....
Forum: Engine Tech 10-08-2014, 11:09 PM
Replies: 26
Views: 892
Posted By Paul Kane
The OEM, real-world compression ratio on your...

The OEM, real-world compression ratio on your engine is about 7.8:1. Your selected 0.030" 88-91 pistons will increase compression to about 9.25:1 +/-. I have nothing against hypereutectic pistons...
Forum: Engine Tech 10-08-2014, 03:00 PM
Replies: 10
Views: 524
Posted By Paul Kane
Yours should pass emissions. I built a similar...

Yours should pass emissions. I built a similar "CA smog legal" engine, 0.030" over 460, massaged 370 heads with 2.08"/1.72" valves, 207*/213*/112 LSA/108 ICL, 8.6:1, etc, put it in an 8600 GVWR...
Forum: Vendor (FOR SALE) 10-08-2014, 02:51 PM
Replies: 15
Views: 5,728
Posted By Paul Kane
http://www.fordforums.com/images/smilies/bump.gif...

http://www.fordforums.com/images/smilies/bump.gif

Paul
Forum: The Auction Block 10-08-2014, 02:50 PM
Replies: 3
Views: 648
Posted By Paul Kane
http://www.fordforums.com/images/smilies/bump.gif...

http://www.fordforums.com/images/smilies/bump.gif

Paul
Forum: Engine Tech 10-07-2014, 11:48 AM
Replies: 9
Views: 602
Posted By Paul Kane
I set the hydraulic flat tappet lash on my jet...

I set the hydraulic flat tappet lash on my jet boat engine at 1/4-turn pre-load and have run it at 5000 rpm sustained for years without needing another adjustment. And when I eventually did check...
Forum: Engine Tech 10-02-2014, 11:20 AM
Replies: 3
Views: 324
Posted By Paul Kane
If you wish to be budget-minded and purchase a...

If you wish to be budget-minded and purchase a set of 1000 hp "rated" I-beam rods that are essentially Crower copies, then the Procomp I-beam for is an excellent value at the $350 retail price. It...
Forum: Vendor (FOR SALE) 09-26-2014, 04:26 PM
Replies: 29
Views: 5,274
Posted By Paul Kane
A.M., Your rocker arm set should have...

A.M.,

Your rocker arm set should have arrived today.

Thanks very much for your business, :cool:

Paul
Forum: Car Buildup Forum 09-25-2014, 11:44 AM
Replies: 130
Views: 12,768
Posted By Paul Kane
http://www.460ford.com/forum/attachment.php?attach...

http://www.460ford.com/forum/attachment.php?attachmentid=37218&d

Everyone note in the above picture that these guys got Jim Holtz in the driver's seat. For those who don't know, Jim Holtz was...
Forum: The Auction Block 09-25-2014, 10:48 AM
Replies: 3
Views: 648
Posted By Paul Kane
Whatever rod length that suits your build, not...

Whatever rod length that suits your build, not only 6.7" or 6.8". If you mean to ask which cookie-cutter rod lengths would get you around zero deck in the combinations listed above, then the 6.8"...
Forum: The Auction Block 09-24-2014, 03:44 PM
Replies: 3
Views: 648
Posted By Paul Kane
Cool Ross Custom Dome Top Stroker Pistons

Ross Forged Pistons for 460 Stroker

Set of brand new Ross domed pistons. These pistons have a small dome, about 0.060" nominal dome height, to increase compression ratio. Standard valve layout...
Forum: Engine Tech 09-19-2014, 11:18 AM
Replies: 22
Views: 968
Posted By Paul Kane
Neither of these links provide direct personal...

Neither of these links provide direct personal experience with the Procomp 8000 distributor that Vandy is discussing. Further yet, both links display a generalized bias against Procomp and virtually...
Forum: Engine Tech 09-19-2014, 10:51 AM
Replies: 22
Views: 968
Posted By Paul Kane
Personally, I prefer the 4.3 stroke, and have a...

Personally, I prefer the 4.3 stroke, and have a good number of 4.3 stroke engines out there on the water running effortlessly and realiably.

I've never been alarmed by water reversion and cam the...
Forum: Engine Tech 09-17-2014, 10:31 AM
Replies: 2
Views: 203
Posted By Paul Kane
Based on the info provided, your oil pressure...

Based on the info provided, your oil pressure behavior sounds perfectly normal everywhere noted. The 8-10 psi at idle is not unusual with a std volume pump in an engine with loose/performance...
Forum: Engine Tech 09-17-2014, 10:24 AM
Replies: 2
Views: 186
Posted By Paul Kane
The D3VE heads and pedestal rockers on the D3VE...

The D3VE heads and pedestal rockers on the D3VE heads use the pushrods that were in the D3VE-headed engine.

The C8VE heads and rail rockers on the C8VE heads use the pushrods that were in the...
Forum: Engine Tech 09-17-2014, 10:20 AM
Replies: 22
Views: 968
Posted By Paul Kane
With your engine combination, application, and...

With your engine combination, application, and when using a blower, yes, you should 4-bolt the block. At the very least you should install a billet steel 2-bolt cap on the number 2 main.

The...
Forum: Engine Tech 09-13-2014, 07:30 PM
Replies: 63
Views: 4,523
Posted By Paul Kane
68xr7cat, I did not state opinion, I stated...

68xr7cat,

I did not state opinion, I stated fact. The info is not useless, it is indeed very useful information and describes what one needs to look for; it simply doesn't answer how to address...
Forum: Engine Tech 09-11-2014, 05:39 PM
Replies: 13
Views: 885
Posted By Paul Kane
Your oil pressure may be on the low side but it...

Your oil pressure may be on the low side but it is still adequate for your engine and its application. Unfortunately, what you do not have is a baseline against which to compare your current oil...
Forum: Engine Tech 09-11-2014, 05:26 PM
Replies: 63
Views: 4,523
Posted By Paul Kane
"...the effective points of the rocker arm are...

"...the effective points of the rocker arm are the centerline of this center bearing (which we call the trunnion) and the centerline of outer roller tip. We we would like is an imaginary line drawn...
Forum: Engine Tech 09-07-2014, 05:48 PM
Replies: 1
Views: 156
Posted By Paul Kane
Sounds and looks good to me--it has the correct...

Sounds and looks good to me--it has the correct hold ID for the bolt, seemingly the correct thickness, and is made of appropriate material. Just keep an eye on it and if the new Evinrude gasket...
Forum: Engine Tech 09-06-2014, 12:19 PM
Replies: 32
Views: 1,001
Posted By Paul Kane
I'm sure at this point that 429CV23 has it clear...

I'm sure at this point that 429CV23 has it clear as day which way to go now. :D

At least we're all trying... :)
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 10:08 AM.



Powered by vBulletin® Copyright ©2000 - 2014, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.