460 Ford Forum - Search Results
Advanced Search
Showing results 1 to 25 of 500
Search took 0.39 seconds.
Search: Posts Made By: TorinoStyle2
Forum: 460Ford.com Site Issues & Website Help   11-11-2015, 12:55 AM
Replies: 62
Views: 2,241
Posted By TorinoStyle2
I dont like all the damn advertising all over the...

I dont like all the damn advertising all over the screen.
This is why I quit going on FordMuscle.com because it took so long to load a page with all the advertisements bombarding the page!!
Forum: 460Ford.com Site Issues & Website Help   11-11-2015, 12:53 AM
Replies: 62
Views: 2,241
Posted By TorinoStyle2
So where are all the different catagories at??

So where are all the different catagories at??
Forum: Engine Tech   11-06-2015, 09:23 PM
Replies: 10
Views: 565
Posted By TorinoStyle2
Put a strait edge on the rails to see if they are...

Put a strait edge on the rails to see if they are flat.
If not, nothing is going to seal them up satisfactorilly.
Forum: Engine Tech   11-06-2015, 03:04 AM
Replies: 10
Views: 565
Posted By TorinoStyle2
The tall Moroso ones. They clear a girdle, and...

The tall Moroso ones. They clear a girdle, and dont look too bad.
Forum: Engine Tech   11-06-2015, 03:02 AM
Replies: 21
Views: 1,066
Posted By TorinoStyle2
This was on one of those famous 100+ degree...

This was on one of those famous 100+ degree Arizona days??
Is it carb'd or EFI??
What kind of fan??
Forum: Engine Tech   10-30-2015, 04:01 AM
Replies: 4
Views: 476
Posted By TorinoStyle2
Well, I rigged up a electric pump from a junkyard...

Well, I rigged up a electric pump from a junkyard Suburban. I figured, what the heck, it only costs $10 and it pulls quite a bit of vacuum. I read somewhere online that they pull 21" inches, but Im...
Forum: The Auction Block   10-30-2015, 12:15 AM
Replies: 7
Views: 1,702
Posted By TorinoStyle2
Sounds like a nice deal. I wonder if that combo...

Sounds like a nice deal. I wonder if that combo could get my heavy Torino deep into the 9's on just motor alone!!
I dont see why not, since my "small" 472 with just a 150 shot was getting me into...
Forum: Engine Tech   10-30-2015, 12:12 AM
Replies: 12
Views: 683
Posted By TorinoStyle2
Yes, the block and heads will work with a stroker...

Yes, the block and heads will work with a stroker kit. As with everything, check all dimensions and clearances. Check with some of the engine kit vendors on this site.
They can set you up with a...
Forum: Car Buildup Forum   10-29-2015, 05:47 AM
Replies: 8
Views: 586
Posted By TorinoStyle2
70bbftorino.....that color is gonna pop in the...

70bbftorino.....that color is gonna pop in the sunlight!! Great color. Cant wait to see it finished.
Are you doing a single stage or multi-stage paint job with it??
Forum: Driveline   10-18-2015, 05:42 PM
Replies: 5
Views: 626
Posted By TorinoStyle2
What gears are in it now??

What gears are in it now??
Forum: Engine Tech   10-18-2015, 05:39 PM
Replies: 4
Views: 431
Posted By TorinoStyle2
Uh, Engine Masters??

Uh, Engine Masters??
Forum: Car Buildup Forum   10-17-2015, 11:56 PM
Replies: 6
Views: 697
Posted By TorinoStyle2
He did mention engine setback, but I think its...

He did mention engine setback, but I think its going to be halfway in to the drivers cabin!!
You gonna attempt this with the stock unibody chassis??
I think its gonna need quite a bit of...
Forum: Engine Tech   10-17-2015, 11:51 PM
Replies: 2
Views: 222
Posted By TorinoStyle2
As long as you're returning the excess back to...

As long as you're returning the excess back to the tank and you have it regulated down to 7 psi or less, theres no problem.
Forum: Engine Tech   10-17-2015, 04:44 AM
Replies: 65
Views: 3,031
Posted By TorinoStyle2
For 6k you can probably piece together a decent...

For 6k you can probably piece together a decent 545/557.
But a large cube motor is going to need heads that can feed it.
Aluminum heads with enough airflow and a modern combustion chamber will pay...
Forum: Engine Tech   10-15-2015, 08:31 PM
Replies: 5
Views: 379
Posted By TorinoStyle2
The VIN number, or partial VIN number should be...

The VIN number, or partial VIN number should be stamped on the block. Usually it is stamped on the drivers side cylinder bank at the rear, just below the cylinder head.
It could be covered with crud...
Forum: Engine Tech   10-13-2015, 11:01 PM
Replies: 3
Views: 571
Posted By TorinoStyle2
Sounds interesting. I think with the mods you...

Sounds interesting. I think with the mods you describe, it will live quite a while at that power level and speed.
As always good machine work and attention to detail along with quality parts (Not...
Forum: Engine Build Archive   10-12-2015, 12:51 AM
Replies: 21
Views: 2,239
Posted By TorinoStyle2
I'll just throw my 2 cents in here!! Tune up...

I'll just throw my 2 cents in here!!
Tune up AND balancing job are important. You can have what they call an "overbalance" done to the rotating assembly where it will be happy in the high RPM zone....
Forum: Engine Tech   10-04-2015, 12:24 AM
Replies: 16
Views: 1,089
Posted By TorinoStyle2
I thought the EPA mandated that the oil companies...

I thought the EPA mandated that the oil companies remove most of the Zinc because of it supposedly clogging up catalytic convertors. I may be wrong, but did this also affect the common brand name...
Forum: Engine Tech   10-03-2015, 02:36 AM
Replies: 16
Views: 1,089
Posted By TorinoStyle2
The advantages are many. Synthetic oil will...

The advantages are many. Synthetic oil will withstand greater heat than regular oil, it is more slippery than regular oil, thus it begins to flow quicker on cold startup's.

You can run a thinner...
Forum: Race Talk   09-18-2015, 07:01 PM
Replies: 1
Views: 497
Posted By TorinoStyle2
This time, Im taking days off of work to go to...

This time, Im taking days off of work to go to it!!
Forum: Engine Tech   09-03-2015, 02:47 AM
Replies: 55
Views: 3,186
Posted By TorinoStyle2
Why not a 632 or more?? with Crower crank 4.750"...

Why not a 632 or more?? with Crower crank 4.750" stroke.
Torque would be very nice!!
Forum: Engine Tech   08-15-2015, 08:51 PM
Replies: 14
Views: 1,096
Posted By TorinoStyle2
Its cool that he's got the Hemi Roadrunner...

Its cool that he's got the Hemi Roadrunner covered....but its even cooler that no Chevy's can touch him!!
Forum: Engine Tech   08-10-2015, 11:17 PM
Replies: 8
Views: 419
Posted By TorinoStyle2
I'd say its at the limit now.

I'd say its at the limit now.
Forum: Engine Tech   08-08-2015, 03:30 AM
Replies: 10
Views: 773
Posted By TorinoStyle2
Are the rods on correctly??..in relation to the...

Are the rods on correctly??..in relation to the crank fillet radius??
Get this backwards, and it will generally be a bear to turn over by hand.
Forum: Engine Tech   08-08-2015, 03:22 AM
Replies: 15
Views: 997
Posted By TorinoStyle2
Baking soda works great for blasting and wont...

Baking soda works great for blasting and wont harm anything.
Showing results 1 to 25 of 500

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome