460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 25 of 68
Search took 0.03 seconds.
Search: Posts Made By: capri476
Forum: General Tech 12-30-2013, 12:31 PM
Replies: 2
Views: 392
Posted By capri476
E4OD

I had to place the cross member back several inches. The drive shaft has to be shortened several inches also.
After having a C6 the E4 is much better for the street.
Gary.
Forum: Engine Tech 09-28-2012, 01:24 PM
Replies: 25
Views: 3,461
Posted By capri476
Hyd. Roller

I have a hydraulic roller with about 6 years and 12,000 miles of street and strip in my 460.
No problems so far. I limit the rpm to 6250 and it pulls strong all the way.
No broken lifters or...
Forum: Driveline 02-14-2012, 08:37 AM
Replies: 27
Views: 7,776
Posted By capri476
E40D

I made this swap in my Fox Mustang with 460 and am very pleased. The C6 and loose converter ran about 3500 rpm at 60 mph and the E40D with converter locked up turns about 2200 rpm.
Much more...
Forum: Engine Tech 01-25-2011, 09:07 AM
Replies: 9
Views: 1,010
Posted By capri476
Fork

On my Fox with a Lakewood bellhousing and a Fox cable operated clutch I used a modified 5.0 fork. I had to add a piece to extend it through the opening and added a pivot to the bell.
Was in for 10...
Forum: Engine Tech 06-21-2010, 08:50 AM
Replies: 6
Views: 1,218
Posted By capri476
gasket

Fel-pro 1231-s3 is available from Summit and other on-line vendors. The plain 1231 is a piece of poop unless its changed very often.
Gary.
Forum: Engine Tech 06-17-2010, 08:38 AM
Replies: 4
Views: 1,030
Posted By capri476
Serpentine Belt

I use a serpentine setup from a 5.0 that I modified to work on my 460. It is in a Fox body Mustang that I mainly use on the street. I added an extra pulley so that my water pump turns the right...
Forum: Engine Tech 11-10-2009, 08:37 AM
Replies: 2
Views: 300
Posted By capri476
Headers

Don.t know about the Supercomps but my headers that were on a 460/c6 fit the e4od just fine.
The closest spot was next to the range sensor.
Forum: Engine Tech 10-21-2009, 09:10 AM
Replies: 14
Views: 1,464
Posted By capri476
Block plate

When I bought my Lakewood shield it didn't come with a block plate and they didn't offer one for sale so I just made one out of 10 gauge steel.
Worked great but had to take a shim out of the starter...
Forum: Engine Tech 09-22-2009, 01:25 PM
Replies: 42
Views: 8,145
Posted By capri476
The tranny from a 460 will fit but all others wll...

The tranny from a 460 will fit but all others wll not. You also have to have a way of controlling the electronics like a Baumann controller.
Forum: Engine Tech 09-16-2009, 11:13 AM
Replies: 10
Views: 1,201
Posted By capri476
I prefer the non Gt rack on a high hp car. The...

I prefer the non Gt rack on a high hp car. The 5.0 rack is 15-1 while the non 5.0 is 18-1. Really feels better to me.
Forum: Engine Tech 09-12-2009, 09:10 AM
Replies: 13
Views: 717
Posted By capri476
The tps is set slightly less than 1 volt at idle...

The tps is set slightly less than 1 volt at idle as it should be. I measure the mass air meter at idle also and at idle it is just about 1 volt. Slightly less than 5 volts at full throttle. You can...
Forum: Engine Tech 09-11-2009, 02:35 PM
Replies: 13
Views: 717
Posted By capri476
My 460 with a stock A9L or A9P with no chip or...

My 460 with a stock A9L or A9P with no chip or tweecer will idle at 850 rpm with a home made mass air and two 65mm throttle bodies.
I bet the mass air is not matched up right. My mass air meter...
Forum: Engine Tech 08-28-2009, 09:12 AM
Replies: 42
Views: 8,145
Posted By capri476
E4OD

The newer 4R100 transmission has the best parts in my opinion and will fit the E4OD case. I used a 96 model case and valve body with an 90 output shaft and 2002 Lightning/Powerstroke planets and...
Forum: Engine Tech 08-26-2009, 01:57 PM
Replies: 42
Views: 8,145
Posted By capri476
Capri

My Capri is an 80 model and you have to make a new transmission crossmember and I use K member spacers that are 1" tall. When I mocked everything up I was using a stock K member and every thing fit...
Forum: Engine Tech 08-25-2009, 10:08 AM
Replies: 42
Views: 8,145
Posted By capri476
E4OD

I have the 460 and E4OD in my Capri Fox body and would never use the C6 again unless it was a track car. 2200 rpm@ 65 instead of 3500 is much better on the engine and my nerves.
The 97 year was the...
Forum: Engine Tech 08-22-2009, 08:30 AM
Replies: 9
Views: 1,227
Posted By capri476
I use a 351 dist. in my 460 with the module on...

I use a 351 dist. in my 460 with the module on the side. You just have to change the gear over.
Forum: Engine Tech 07-10-2009, 09:01 AM
Replies: 10
Views: 1,092
Posted By capri476
Hydraulic roller

I have used a Crane hydraulic roller in my street car for about 5 years now and am completely satisfied! The valve covers are a pain to get off with the efi and I believe the hydraulic rollers just...
Forum: Chilly's Garage 03-26-2009, 08:55 AM
Replies: 18
Views: 732
Posted By capri476
Life member here of NRA and TSRA!

Life member here of NRA and TSRA!
Forum: Engine Tech 03-24-2009, 09:02 AM
Replies: 87
Views: 6,694
Posted By capri476
Roll Pin

I had a roll pin break in my wifes 429 Mustang, I beefed it up and a month later I had to tow her home when the distributer gear broke! In the oil pump I found a tiny piece of hard wire and I thought...
Forum: Engine Tech 03-13-2009, 03:06 PM
Replies: 10
Views: 986
Posted By capri476
I use the 1231-S3 Fel-Pro as it has a steel...

I use the 1231-S3 Fel-Pro as it has a steel liner. The 1231 gasket has always caused problems on my engine with intake port gasket distortion and even some water leakage. Gary.
Forum: Engine Tech 02-26-2009, 12:01 PM
Replies: 25
Views: 1,612
Posted By capri476
Are the rod bearings the right size?

Are the rod bearings the right size?
Forum: General Tech 02-25-2009, 09:28 AM
Replies: 8
Views: 1,981
Posted By capri476
I have an E4OD in my Mustang that I love . It is...

I have an E4OD in my Mustang that I love . It is a little larger and is about six inches longer but will fit if you have the desire. Drops my highway cruise from almost 3500 rpm with the C6 and a...
Forum: General Tech 02-24-2009, 08:47 AM
Replies: 4
Views: 402
Posted By capri476
I have one in my Fox body and it is out of a late...

I have one in my Fox body and it is out of a late model Mustang . It gives extra clearance for valve covers and really works good. My son also uses one in his 67Stang and was fairly easy to install....
Forum: Engine Tech 02-13-2009, 09:08 AM
Replies: 5
Views: 676
Posted By capri476
MD84HV

MIne opens the bypass at about 80 psi like was stated. When hot and at rpm my engine runs about 70 psi and 40 idle.Gary.
Forum: Engine Tech 02-09-2009, 11:00 AM
Replies: 7
Views: 743
Posted By capri476
Make sure of the pilot bearing tip on the...

Make sure of the pilot bearing tip on the toploader is the correct length. Some are a bit longer and will bind the tranny up if there is a mismatch of parts.
I have had to cut about a quarter inch...
Showing results 1 to 25 of 68

 
Forum Jump

All times are GMT -5. The time now is 05:19 AM.



Powered by vBulletin® Copyright ©2000 - 2014, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.