460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 25 of 294
Search took 0.04 seconds.
Search: Posts Made By: DanE
Forum: Engine Tech 02-10-2015, 08:34 PM
Replies: 37
Views: 1,782
Posted By DanE
Yes, I meant a 1970 short block and D3 heads....

Yes, I meant a 1970 short block and D3 heads. Thank you for calling it to my attention.
Forum: Engine Tech 02-10-2015, 04:45 PM
Replies: 37
Views: 1,782
Posted By DanE
Sooper Camper; Either a Dove head and a...

Sooper Camper;

Either a Dove head and a dished piston or D3 head with a flat top piston is a viable choice.

I clarified by saying is was offering my opinion on an economical approach....
Forum: Engine Tech 02-10-2015, 11:06 AM
Replies: 37
Views: 1,782
Posted By DanE
Sooper Camper; To be kind but blunt, your...

Sooper Camper;

To be kind but blunt, your are right, you are not getting it. You have had some VERY knowledgeable people trying to give you the help you asked for, and it does not seem to be...
Forum: Engine Build Archive 01-25-2015, 03:16 PM
Replies: 3
Views: 393
Posted By DanE
Hey Sam; Contact one of the vendors on this...

Hey Sam;

Contact one of the vendors on this site and discuss your project with them. They know the 460 engine inside out. Do as they say and buy the parts you need from them or where they tell you...
Forum: Engine Tech 01-21-2015, 09:06 AM
Replies: 4
Views: 280
Posted By DanE
Did you mean 1.7 Chevy rockers or 1.73 Ford...

Did you mean 1.7 Chevy rockers or 1.73 Ford rockers? Different geometries.
If I was going to pick one of the cams you listed, I would pick the Lunati 10340700. However, I would contact one of the...
Forum: Engine Tech 01-02-2015, 01:27 PM
Replies: 11
Views: 500
Posted By DanE
Ranger; Using the figures you supplied...

Ranger;

Using the figures you supplied above, lets figure your compression the old long hand way using the conversion factor of 1000cc equals 61.024 cubic inches.
When the piston is a top dead...
Forum: Engine Tech 12-27-2014, 08:07 PM
Replies: 4
Views: 360
Posted By DanE
I believe that a recurved distributor is the...

I believe that a recurved distributor is the single biggest bang for the buck in hot rod land.
Forum: Engine Tech 12-25-2014, 12:07 PM
Replies: 22
Views: 1,444
Posted By DanE
You don't specify your cam. While you are talking...

You don't specify your cam. While you are talking to the vendor, he will ask the necessary questions so as to be able to supply you with a cam to suit your needs. Odds are he will not supply a...
Forum: Engine Tech 12-25-2014, 10:26 AM
Replies: 22
Views: 1,444
Posted By DanE
Take it easy on you, sure, no reason not to. ...

Take it easy on you, sure, no reason not to. "HAPPY HOLIDAYS"

Part of asking for advice is listening to the advice given. You had two answering posts that advised you to get a custom cam to suit...
Forum: Engine Tech 12-19-2014, 05:15 PM
Replies: 41
Views: 2,546
Posted By DanE
What Carl stated is a fact. NOT an opinion. ...

What Carl stated is a fact. NOT an opinion.
You are stating opinions as facts.
Forum: Engine Tech 12-19-2014, 12:53 PM
Replies: 41
Views: 2,546
Posted By DanE
NO. Do a search on this site for appropriate...

NO. Do a search on this site for appropriate roller cams for a 460. Is this project a street vehicle or a strip vehicle or what?
Forum: Engine Tech 12-17-2014, 04:43 PM
Replies: 7
Views: 515
Posted By DanE
I started this post earlier this morning, just...

I started this post earlier this morning, just got back, and finished it. After posting I saw that Randy had already covered the subject.
Forum: Engine Tech 12-17-2014, 04:30 PM
Replies: 7
Views: 515
Posted By DanE
X2 The Stealth was not designed for what you...

X2 The Stealth was not designed for what you want to do. Do a search on this site.

Seeing as how you are going to purchase new pistons, get a 460 crank and use your exsisting rods. 460 piston...
Forum: Engine Tech 12-16-2014, 07:04 PM
Replies: 21
Views: 1,600
Posted By DanE
I and a lot of other people have put stock CJ...

I and a lot of other people have put stock CJ intakes on the passenger car heads and noticed an increase. Matching the heads to the intake does not seem to be worth the effort.
Forum: Engine Tech 12-16-2014, 06:50 PM
Replies: 31
Views: 1,257
Posted By DanE
I don't like the Flowmaster mufflers either and...

I don't like the Flowmaster mufflers either and they are somewhat restrictive also unless they have brought out something different recently.

Around 500 HP is the line between 2 1/2" pipe and 3'...
Forum: Engine Tech 12-16-2014, 08:28 AM
Replies: 31
Views: 1,257
Posted By DanE
Beautiful car! What is the exhaust behind the...

Beautiful car! What is the exhaust behind the headers?
Forum: Engine Tech 12-15-2014, 01:11 AM
Replies: 14
Views: 578
Posted By DanE
And your hesitating?

And your hesitating?
Forum: Engine Tech 12-15-2014, 01:06 AM
Replies: 16
Views: 1,130
Posted By DanE
YOU MUST BE HARD OF HEARING, BECAUSE YOU SURE...

YOU MUST BE HARD OF HEARING, BECAUSE YOU SURE TALK LOUD. MUST BE ALL THOSE YEARS LISTENING TO OPEN HEADERS! ACTUALLY, ME TOO, SAME REASON.

BEST
Forum: Engine Tech 12-14-2014, 09:36 PM
Replies: 16
Views: 1,130
Posted By DanE
Why someone would build a 521 and not have their...

Why someone would build a 521 and not have their foot in it, I don't know, but, seeing as how you claim you don't, install a hydraulic flat tappet cam in it, and sell your roller cam and springs and...
Forum: Engine Tech 12-14-2014, 09:09 PM
Replies: 31
Views: 1,257
Posted By DanE
Those headers probably don't leave any HP on the...

Those headers probably don't leave any HP on the table til about the 600 HP mark and they probably provide an increace in torque, so, the question is, how much HP does your engine make now?
Forum: Engine Tech 12-14-2014, 10:47 AM
Replies: 21
Views: 1,600
Posted By DanE
When I did the search, it took me to E-Bay and...

When I did the search, it took me to E-Bay and there was a Blue Thunder intake in the auction block for $540 outright or bid on it. I bought a standard port Blue Thunder dual quad, dual plane intake...
Forum: Engine Tech 12-14-2014, 08:47 AM
Replies: 21
Views: 1,600
Posted By DanE
I read your post, typed "460 dual quad intake" in...

I read your post, typed "460 dual quad intake" in the search function on this site and there were 2 intakes listed. Your not trying very hard.
Forum: Engine Tech 12-05-2014, 06:30 PM
Replies: 18
Views: 1,172
Posted By DanE
[QUOTE=DaveMcLain;1372202]I don't think that the...

[QUOTE=DaveMcLain;1372202]I don't think that the amount of lash has much to do with contact velocity. That's all in the design of the ramp.[

That's the theory, probably not the reality. There's...
Forum: Engine Tech 12-05-2014, 09:59 AM
Replies: 18
Views: 1,172
Posted By DanE
10. Use lobe profile that requires a tighter lash...

10. Use lobe profile that requires a tighter lash so as to lessen the hammering effect each time valve lash clearance is taken up.
Forum: Engine Tech 12-03-2014, 03:03 PM
Replies: 13
Views: 688
Posted By DanE
Hey Fordtrucknut77; Go to Speedtalk.com,...

Hey Fordtrucknut77;

Go to Speedtalk.com, click on engine tech, and open this thread.

"Failed Isky EZ Roll bushing type solid roller lifter"

There is a lot of information in that thread...
Showing results 1 to 25 of 294

 
Forum Jump

All times are GMT -5. The time now is 11:28 PM.



Powered by vBulletin® Copyright ©2000 - 2015, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.