460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 25 of 68
Search took 0.03 seconds.
Search: Posts Made By: colormebad
Forum: General Race Tech 04-27-2014, 03:43 PM
Replies: 1
Views: 286
Posted By colormebad
Coated Or None Coated Bearings ??

Which seems the best to run in a drag racing engine? Coated or none coated Rod & Main Bearings ???
Forum: General Tech 03-20-2014, 05:01 PM
Replies: 0
Views: 150
Posted By colormebad
Question Cyl Or Thread In Intake Port ??

I noticed when i pulled my heads to replace my cometic gaskets, Oil/Gas left marks in the valve pocket...Does it look like it came from the threaded hole that holds my shaft mount rocker down to head...
Forum: General Race Tech 03-09-2014, 08:36 PM
Replies: 0
Views: 292
Posted By colormebad
Vavoline 20/50 Turning Dark after 4 passes ?

Im running C16 racing fuel, and never had this problem before, but just put new oil and filter and made 4 passes at the track and the oil looks dark...I have had this oil in boxes when it was on sale...
Forum: General Tech 02-18-2014, 10:12 PM
Replies: 0
Views: 240
Posted By colormebad
Strongest C4 Forward Drum ??

Which of the 2 drums seem to be holding up the best, between welded or the sleeve ??

http://i914.photobucket.com/albums/ac341/billykristall/2-18-201420-00-34_zps4212ba7a.jpg...
Forum: Engine Tech 02-11-2014, 04:30 PM
Replies: 1
Views: 149
Posted By colormebad
What would be the best size header for my combo ??

What would be the best size header for my combo ??
438 sbf
14:1 compression
Brodix 201 heads
2 fogger setup
Glidden Victor Intake

I was looking at what i had been running right here, except a...
Forum: General Tech 02-02-2014, 03:07 PM
Replies: 2
Views: 247
Posted By colormebad
Aerospace Brake Problem ?

I have tryed everything i know and i still have hardly any brakes...I can stop the car , but its like being in a regular car and turning off the engine, and then press the brakes...Feels a little...
Forum: General Tech 01-25-2014, 02:34 PM
Replies: 2
Views: 405
Posted By colormebad
How Safe Is A VW Front Runner Tire ??

I done wheelies for years and coming down hard, never any problems...How safe you guys think a VW tire is...Also how safe going faster ???
Forum: General Race Tech 10-30-2013, 06:40 PM
Replies: 0
Views: 494
Posted By colormebad
Converter Or Carb/Fuel Problem ?

I have a friend that has a 408 sbf running nos...When he tested on just motor, it bogs bad off the line through about the 60-80 mark, then runs fine...On nos it leaves like a bullet...In these links...
Forum: General Race Tech 10-08-2013, 08:51 PM
Replies: 0
Views: 383
Posted By colormebad
Cyl Bore ?

How much problem would this mark cause ?

http://i914.photobucket.com/albums/ac341/billykristall/10-8-20136-45-33PM_zps48c15ab9.png...
Forum: General Race Tech 08-22-2013, 08:02 PM
Replies: 0
Views: 289
Posted By colormebad
Valve Stem Pitting On New Victory Valves ?

My engine has only had about 3 hours total running on engine since built & when i sent my valves back to Victory they said some pitting on the stems above tulip area..Said they would be fine..They...
Forum: General Race Tech 08-08-2013, 07:10 PM
Replies: 1
Views: 387
Posted By colormebad
Exh VAlve ?

Engine has less that 3 hours running over the past year since built new..Went back to re-tq head studs and noticed all the exh valves only, had a wear pattern and you could hang your nail on it just...
Forum: General Race Tech 07-16-2013, 12:18 PM
Replies: 1
Views: 491
Posted By colormebad
Biggest Pushrod For Brodix 201 Head ?

Anyone know if a 1/2 pushrod will work on the brodix 201 head ? running 7/16 right now...
Forum: Engine Tech 07-03-2013, 05:08 PM
Replies: 6
Views: 519
Posted By colormebad
Every layer was sprayed with copper coat...We...

Every layer was sprayed with copper coat...We used a camera and can't find any oil anywhere except in this area..Has to be coming from standing oil, Engine has been ran in a week ..But every 6 hours...
Forum: Engine Tech 07-02-2013, 12:52 PM
Replies: 6
Views: 519
Posted By colormebad
Cometic Gasket Weeping Oil ?

Have a friend with one side only, weeping a very very small amount of oil on drivers side toward back...He said he never re-tq'd the heads after running with new rebuild...He said it only shows a...
Forum: General Tech 06-30-2013, 04:00 PM
Replies: 1
Views: 300
Posted By colormebad
Alignment Or K-Member ?

I never paid attention if the driver tire was out more than the pass tire, Till after the alignment...Could this be a K-member problem? The driver tire is out a good bit more than the pass & is it...
Forum: General Tech 06-25-2013, 07:37 PM
Replies: 0
Views: 206
Posted By colormebad
Aerospace Brake Caliper Bleed ?

I have the 4 piston for a sn95 and still having hard pedal issues.Aerospace said take the caliper off and face the bleeder straight up and bleed them..I ask alot of other racers about this' and they...
Forum: General Race Tech 06-08-2013, 11:08 AM
Replies: 2
Views: 413
Posted By colormebad
Disc - Drum Master Cyl ?

Whats a good master cyl that will work with disc on front and drum on rear, For a 95 mustang ? Have a Strange Engineering B3359, but brakes are real hard...
Forum: General Race Tech 06-01-2013, 11:06 PM
Replies: 7
Views: 1,001
Posted By colormebad
I found it here on this site....I have them at...

I found it here on this site....I have them at 6:00...So i guess i been lining the pigs up right all these years..LoL
...
Forum: General Race Tech 06-01-2013, 11:44 AM
Replies: 7
Views: 1,001
Posted By colormebad
Sorry' i guess your a teenager , if you have...

Sorry' i guess your a teenager , if you have never heard of a spring pigtail...:cool:
Forum: General Race Tech 06-01-2013, 10:34 AM
Replies: 7
Views: 1,001
Posted By colormebad
Rear Spring Pigtail Location?

I was told that the ends of the pigtails should face the driver side on both springs. Or the car would sit unlevel...Is this true ? I had always had the end of the pigtail facing toward the rear in...
Forum: Wheel and Tire Tech 05-22-2013, 07:04 AM
Replies: 4
Views: 2,101
Posted By colormebad
It dont seem to stick out at all...Seems just...

It dont seem to stick out at all...Seems just right....Its a 10" rim...The center of the tire is no where close to the outside , where the 1" clearance is..I will post a pic where i reworked that...
Forum: Wheel and Tire Tech 05-20-2013, 04:57 PM
Replies: 4
Views: 2,101
Posted By colormebad
Tire To Fenderwell Clearance ?

How much clearance would work ok' With a 29.5X10.5 Drag Slick ? I have 1" in the front and rear of the fenderwell...
Forum: Driveline 04-30-2013, 10:58 PM
Replies: 5
Views: 843
Posted By colormebad
Been building them for years and have some cars...

Been building them for years and have some cars running 4.80's with the c4's i build...That i dont worry about...They are not running transbrakes
Forum: Driveline 04-30-2013, 05:26 PM
Replies: 5
Views: 843
Posted By colormebad
Transbrake VS RMVB

Would a person not be better off using a Reverse Manual Valve Body' Running a C4 trans...I know how how these little C4 leaves the line , and thought the RMVB would be easier on the clutches & the...
Forum: The Auction Block 04-09-2013, 09:05 PM
Replies: 1
Views: 326
Posted By colormebad
BRAND NEW MSD 6AL / BLASTER 3 COIL

BRAND NEW MSD 6AL IGNITION ..... BLASTER 3 COIL.... MOUNTED ONLY LONG ENOUGH TO FIRE NEW ENGINE A FEW TIMES..... $200 + Shipping
...
Showing results 1 to 25 of 68

 
Forum Jump

All times are GMT -5. The time now is 02:30 AM.



Powered by vBulletin® Copyright ©2000 - 2014, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.