460 Ford Forum - Search Results
460 Ford Forum  
Go Back   460 Ford Forum > Search Forums

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 25 of 474
Search took 0.16 seconds.
Search: Posts Made By: bigblockpaul
Forum: The Auction Block 10-20-2014, 08:42 PM
Replies: 0
Views: 96
Posted By bigblockpaul
Glide manual valvebody

its a stock body with the TSR racing inerds.fully manual.I only pulled out to go trans brake. It worked great...100.00 you ship.Iam in Minnesota
Forum: The Auction Block 10-20-2014, 08:39 PM
Replies: 7
Views: 206
Posted By bigblockpaul
try

Holcomb motorsports has new ones for 24.00 a piece...1-800-475-7223
Forum: Race Talk 10-06-2014, 07:10 PM
Replies: 1
Views: 100
Posted By bigblockpaul
new personal best times

went 10.53 at 129 sat at Cedar Falls raceway.476 bbf with tunnel ram and two 600 carbs and a glide.Was a blast i hot lapped it till i was out of gas..What a great day.
Forum: The Auction Block 10-01-2014, 09:18 AM
Replies: 1
Views: 156
Posted By bigblockpaul
460 main bearings stock size

Got a full main set cle ms1039 p...stock size.speed shop sent wrong ones and then closed shop.30.00 you ship
Forum: Chilly's Garage 09-29-2014, 06:36 AM
Replies: 6
Views: 535
Posted By bigblockpaul
Bigfoot monster truck.

I looked at one at gateway racetrack and was very discussed.The truck had a Chevy motor.What the hell...
Forum: General Race Tech 09-23-2014, 08:28 PM
Replies: 7
Views: 634
Posted By bigblockpaul
plugs

???
Forum: The Auction Block 09-22-2014, 08:52 PM
Replies: 11
Views: 533
Posted By bigblockpaul
not yet

checked mail today and no.
Forum: The Auction Block 09-12-2014, 07:21 PM
Replies: 11
Views: 533
Posted By bigblockpaul
sale pending

payment
Forum: The Auction Block 09-11-2014, 08:45 PM
Replies: 11
Views: 533
Posted By bigblockpaul
never

never got the pm from sept 11?
Forum: The Auction Block 09-04-2014, 10:56 PM
Replies: 11
Views: 533
Posted By bigblockpaul
price lower

125.00 o.b.o...
Forum: The Auction Block 08-24-2014, 07:29 PM
Replies: 5
Views: 482
Posted By bigblockpaul
sorry

I forgot that I Evan posted this on here.I bought a new one sorry.
Forum: The Auction Block 08-20-2014, 08:26 PM
Replies: 11
Views: 533
Posted By bigblockpaul
Mallory dist

for 460.unalite with mech advance.with active power filter.175.00...you ship...with new rotor and cap.
Forum: The Auction Block 08-08-2014, 11:28 PM
Replies: 5
Views: 482
Posted By bigblockpaul
wanted dist

looking for a dist msd part #8577
Forum: The Auction Block 08-08-2014, 06:37 PM
Replies: 2
Views: 270
Posted By bigblockpaul
mounts

sale pending
Forum: The Auction Block 08-04-2014, 08:40 PM
Replies: 2
Views: 270
Posted By bigblockpaul
460 foxbody motor mounts

got a used set of motorsport mounts for 460 in a fox...used 50.00 you ship...
Forum: The Auction Block 08-04-2014, 08:39 PM
Replies: 2
Views: 259
Posted By bigblockpaul
main studs

sold
Forum: Engine Tech 07-28-2014, 08:33 PM
Replies: 1
Views: 159
Posted By bigblockpaul
re red hot header tubes.

yup you guys were right.i fired it up put timing in it and the pipes cooled down in the 400 range and they all were close.got cam broke in and gonna drive it when back from vac.thanks to all who...
Forum: Engine Tech 07-25-2014, 08:59 PM
Replies: 9
Views: 419
Posted By bigblockpaul
472

heads are fully worked edel 6079 small chambers.and the timming was in the 20.s total.i did not really have time to set it.how hot is too hot.my heat gun was in the 600 degrees.should i try and run...
Forum: The Auction Block 07-25-2014, 06:57 PM
Replies: 0
Views: 81
Posted By bigblockpaul
push rods

got a used set of trick flow 8.700 inch 5/16 rods....100 new mine 50.00 plus shipping
Forum: The Auction Block 07-25-2014, 06:55 PM
Replies: 2
Views: 259
Posted By bigblockpaul
studs

sale pending
Forum: Engine Tech 07-25-2014, 06:53 PM
Replies: 9
Views: 419
Posted By bigblockpaul
help red hot header tubes

new build 472.during cam break in had to shut it off due to #7 and 8 header tubes glowing red.really hot.shut if off to check plugs.they looked way lean.It has a tunnel ram with 2 vac secondary 600...
Forum: The Auction Block 07-23-2014, 10:55 PM
Replies: 2
Views: 259
Posted By bigblockpaul
arp main studs 460

part #155-5402 used but in great shape 60.00 you ship...went to a Canton girdle and it uses arp bolts..
Forum: Engine Tech 07-17-2014, 08:36 PM
Replies: 5
Views: 233
Posted By bigblockpaul
new cam

can i use the lifters from old cam.they all look great.its a solid lifter cam.went bigger and have the set of used lifters with the oiling hole in bottom.
Forum: Engine Tech 07-16-2014, 08:29 PM
Replies: 8
Views: 387
Posted By bigblockpaul
yes

good info from all.i did have a cheapo balancer when this happened.this time i got a good one and had the whole rotating assembly balanced.and did order a Canton one.
Forum: Engine Tech 07-16-2014, 06:18 PM
Replies: 8
Views: 387
Posted By bigblockpaul
girdle

I got good rods and main studs.and still had cap walk so I wanted some additional help.I know that girdles aren't for everyone.
Showing results 1 to 25 of 474

 
Forum Jump

All times are GMT -5. The time now is 05:08 AM.



Powered by vBulletin® Copyright ©2000 - 2014, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.