Valve cover torque lbs - 460 Ford Forum
460 Ford Forum  
Go Back   460 Ford Forum > Tech Topics > Engine Tech

Engine Tech A place to discuss all 385-series engine tech and theory.

460Ford.com is the premier 460 Ford Forum on the internet. Registered Users do not see the above ads.
Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 04-08-2010, 06:40 PM
donwhis donwhis is offline
Member
 
Join Date: Dec 2009
Posts: 76
donwhis First On Race Day
Default Valve cover torque lbs

I got my engine with a set of old Holley cast aluminum valve covers. Stock steel covers use 10 lbs of torque, what would be right for the cast aluminum? I am using Felpro 3/16" steel core cork-lam gaskets.

Last thing I want to do is break/crack the covers!!!!
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
  #2  
Old 04-08-2010, 09:37 PM
johnnywalker johnnywalker is offline
Member
 
Join Date: Aug 2007
Location: jackson michigan
Posts: 200
johnnywalker Driving a Ford
Send a message via Yahoo to johnnywalker
Default

is that 10 inch lbs or 10 foot lbs ? that little bolt will only take so much torque before it brakes !! so make sure .
Reply With Quote Quick reply to this message
  #3  
Old 04-09-2010, 03:23 AM
shawnlee shawnlee is offline
Member
 
Join Date: Apr 2006
Location: ventura .ca.
Posts: 248
shawnlee Driving a Ford
Default

Here is what I like to do...........

Coat the valve cover side with aviation gaskett sealer,coat the valve cover with aviation sealant.
Then stick the gaskett to the valve cover..............then depending on if this is track engine or 100,000 mile street engine....if a track engine just lightly coat the head side of the gaskett with silicone sealer........possibly no silicone depending on how often the valve cover has to come off................if it is a street engine with a hydraulic cam that needs no valve adjustment I will put aviation sealant on the head side also.

Then snug the bolts down at about half the torque you will finally use...let it stand overnight ,then fully tighten the bolts down.....I have no idea what the actuall torque spec is for the valve cover...........I just use a 1/4 inch drive ratchet and tighten them down good and snug.......it is something you develope a feel for as to how tight ,then I also use blue loctite on the bolts and clean the threads really well first ,I usually use brake clean for the bolts and use a q-tip soaked in brake clean for the bolt holes.

Some would say that it overkill to do it this way ,but I very seldom have leaks and they stay put when installed in this manner.

I would think you would have to really go pretty tight to break the valve covers or have mushy thick gasketts to break the valve cover ears off from tightening them.........I also like to use the metal reinforced rubber gasketts ,but I am sure the reinforced cork will work fine also.

I did a quick search and 4 to 7 ft pounds seems like the normal recomendation for most of them.

I think you would be safe with 7 to 10 ft lbs considering your gaskett choice....but I would feel it out and if that seems too tight STOP.....

In my mind it would be better to have them too lose at first and have to tighten them ,rather than stripping/breaking a bolt off or crushing the gaskett.

Well thats my 2 bits anyway..........hopefully someone will give you the correct torque spec soon.
Reply With Quote Quick reply to this message
  #4  
Old 04-09-2010, 03:19 PM
donwhis donwhis is offline
Member
 
Join Date: Dec 2009
Posts: 76
donwhis First On Race Day
Wink

Thanks for the help. I used 7 ft lbs and had to retighten after they sat for a few hours. Finally got into Holley tech support but they didn't have any torque specs for their old covers. So, I will go with this and check them again after the engine has been run and warmed up.
Reply With Quote Quick reply to this message
  #5  
Old 04-09-2010, 09:03 PM
White Lightning's Avatar
White Lightning White Lightning is offline
Senior Member
 
Join Date: Feb 2010
Posts: 4,808
White Lightning First On Race Day
Default

1/4" bolt.....7 Ft lbs...about what you can turn with a screwdriver handle.
__________________
Rob Hawes-Anchorage Rod Works-Anchorage, Alaska
Reply With Quote Quick reply to this message
  #6  
Old 04-10-2010, 01:23 AM
95lightiningguy 95lightiningguy is offline
Senior Member
 
Join Date: Sep 2009
Location: N.Little Rock AR
Posts: 938
95lightiningguy First On Race Day
Send a message via Yahoo to 95lightiningguy
Default

I always tighten them down a nut driver as hard as I can and never had a leak nor have I ever broke anything.
__________________
89 F150 351w powered
95 F150 300 I6 5 speed soon to be 460 powered lightining clone
Reply With Quote Quick reply to this message
  #7  
Old 04-10-2010, 10:32 AM
rmcomprandy rmcomprandy is offline
Senior Member
 
Join Date: Jan 2006
Location: Roseville MI
Posts: 9,639
rmcomprandy Bleeding Blue
Default

Right out of a Chiltons manual - "Tighten till fully seated, not to distort the gasket".
I'm gonna make the guess that the GASKET material and strength will determine the torque,,,
__________________
www.rmcompetition.com

R.M. Competition - The finest Custom Engine Building for any venue ... !
Selling Parts and Supplies from companies I use ... 1(586)909-1591

CUSTOM ground camshafts
Carburetor modifications for specific applications
CNC porting
Reply With Quote Quick reply to this message
  #8  
Old 04-10-2010, 10:59 AM
White Lightning's Avatar
White Lightning White Lightning is offline
Senior Member
 
Join Date: Feb 2010
Posts: 4,808
White Lightning First On Race Day
Default

Quote:
Originally Posted by rmcomprandy View Post
Right out of a Chiltons manual - "Tighten till fully seated, not to distort the gasket".
I'm gonna make the guess that the GASKET material and strength will determine the torque,,,
X2
__________________
Rob Hawes-Anchorage Rod Works-Anchorage, Alaska
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the 460 Ford Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:35 PM.



Powered by vBulletin® Copyright ©2000 - 2014, vBulletin Solutions, Inc.

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.