460 Ford Forum banner

1 - 19 of 19 Posts

·
Registered
Joined
·
78 Posts
Discussion Starter #1 (Edited)


Additional Phots at:

http://s264.photobucket.com/albums/ii185/ssexton1966/

1966 Fairlane (I need to clear Fl title through DMV never did it because its a race car, not street legal)
2x3 box tube frame from firewall to rear bumper
1 3/4x.125 wall seamless 12 pt. Cage tied to shock towers
C/E ladder bar susp. w/ alden coil overs.
9” stange 31 spl. Spool, non Nodular
Turbo action tranny/8” converter (New, uninstalled) TCI pan, sheild flywheel sheild.
Turbo action shifter (New, uninstalled)
Poly seats
New rebuilt front suspension has less than 15 runs on car.
Body
New Nason paint, lexan all around (.125”) Dzus hood and trunk

Car weighs 2750# minus driver

Engine
460 (Update- engine is assembled, will finish assembling car to running status this week, maybe finish by next week)
Unassembled, needs machne work to heads/block and reassembled.
Speed pro popups (L2443?) New and clearanced for cam w/Lindy tool (Included in sale)
Comp Cams solid .600+ have specs.
Milodon Pan 9Qt.
Eagle Ibeam rods
Steel SFI balancer
Aluminum water pump
Port-o-sonic w 950 proform (Carb new in the box)
All new ignition in the box MSD Dist./7AL2 box, MSD Coil
Car is plumbed and wired. Aluminum Fab Fuel cell Holl Elect pump (Blue)

I have to sell now because I am going through a divorce, so will sell the whole lot for $6 k (Edited 6/17/2013)

Call Cell 561-239-3103 for more Info.

Thanks
Shawn

Why selling?
Need funds for daughter’s new car! Will get back into racing later when expenses permit.

Next stop EBAY if I don’t sell here first!
 

·
Registered
Joined
·
78 Posts
Discussion Starter #2
Forgot a couple things

Forgot to mention I have hooker 2 1/8 headers and Dynamax mufflers 3.5" tubes to rear end w/Down tubes as well.
 

·
Registered
Joined
·
78 Posts
Discussion Starter #3
Oops

And the hits just keep coming!

Forgot to mention engine has Dove heads complete port job, need to finish up w/machine work, all new manley valves, comp springs, retainers, locks, seals, screw in studs, harland sharp roller rockers, 3/8 rods, FMS valve covers.

Hope that's everything, I'll have to ook in my garage to make sure.
 
D

·
Guest
Joined
·
0 Posts
It be a good idea to post some more detailed pistures of the chassis, engine, rear, Suspension, ect.

Is the Chassis Certified? Who Built it?
 

·
Registered
Joined
·
78 Posts
Discussion Starter #6
Thanks

Thanks for the suggestions, will take more photos and post in the bucket.
The car was built by Thompsons fabrications in south Florida. Chassis is not certified. Have gone mid 11's w/ very mild street motor/trans combo
.030 over 460/stock tans w/manual/reverse/10" converter and only 3/4 throttle, since the peddle bottomed out on the firewall at that amount. Never found out how fast it would have gone though.

Anyway bought my daughter a new car and have to pay for it somehow, so this has to end for a while, maybe till she's done with college, then I can get back to it with another car.
 

·
Registered
Joined
·
78 Posts
Discussion Starter #8
One more time

Will try once more... Still for sale, will negotiate price for serious offer.

Cell- 561-239-3103
 

·
Registered
Joined
·
78 Posts
Discussion Starter #10 (Edited)
Up for sale again

Up for sale again, have to get it back together and running first, hopefully the next couple weeks and I can post some results.

I have to sell now because I am going through a divorce, so will sell the whole lot for $6 k

will include extras like fenders, bumpers, extra rear wheels, tires, engine stand and hoist go with it too.

call me at 561-239-3103 live in south Palm Beach county, Florida, which is a looonnnggg
way if you're in Walla Walla Washington! (You have to pick up or if I deliver for extra $$ negotiated later)

(Update- engine is assembled, will finish assembling car to running status this week, maybe finish by next week)
 

·
Registered
Joined
·
78 Posts
Discussion Starter #14
Heads are dove castings, lots of port work done by me, Manley S/S valves 2.25/1.76
Comp springs, screw in studs and guide plates for 3/8" pushrods (Manley)

3 angle valve seats by the local machine guy in Stuart Florida. (He did all the machine work/balance for me).

Have yet to start/break in the motor.
 

·
Registered
Joined
·
248 Posts
Damn thats a good deal for that car, wish I didnt spend all my funds on my current build, I have a nice 501 that would work great in that car @ 2750 pounds ....GLWS
 

·
Registered
Joined
·
78 Posts
Discussion Starter #17
Thanks for the good word guys- I hate to see it go, but will be homeless shortly (Translation: NO GARAGE!!! Arghhhh!!)

I have every confidence that I'll be back into the game in the future though, so I'll be back!!
 

·
Registered
Joined
·
78 Posts
Discussion Starter #18 (Edited)

·
Registered
Joined
·
248 Posts
Thanks for the good word guys- I hate to see it go, but will be homeless shortly (Translation: NO GARAGE!!! Arghhhh!!)

I have every confidence that I'll be back into the game in the future though, so I'll be back!!

Damn it, You got me wanting to sell off some stuff to come get this car ! lol
 
1 - 19 of 19 Posts
Top