460 Ford Forum banner

1 - 19 of 19 Posts

·
Registered
Joined
·
697 Posts
Discussion Starter #1
Low Mileage 466 motor for sale from carb to oil pan, FREE BBF C6

Alright guys i have about 1000ish miles on my 466 that i want to sell off completely minus accessories brackets. here is a short run down of the motor:

71 block
c9ve heads (the good ones) ( roofs raised and humps removed )
cobra jet rods with arp rods bolts
forged pistons with -24cc dish
9.4-9.5 CR (i mainly ran 89 octane)
crane 1.7 rocker arms
weiand stealth
Comp cam xe274 cam
custom cal'd carb to motor 800cfm DP (de horned and etc and flows 850)
stock oem oil pan
stock valve covers
std volume oil pump

I ran a best of 12.69 with this motor and trapped at 108MPH. according to the HP chart, i should be around the 450-475HP range at minimum.

if you are local, i want wait for you to see the motor run and maybe go out for a spin with me. i really don't want to go long periods of times having this motor sit and especially when a buyer can possibly see it run before buying.

i'm thinking with a complete motor minus accessories brackets looks good at $2500 or OBO. i'm also wanting to sell off the automatic engine plate, and flexplate with the motor.

if you really want, i will throw in the c6 thats been sitting out in the rain for FREE. it was mated with the motor originally before the tko600.

i am located near SACRAMENTO CA!!!

--------------------------------------------------------------------------------
 

·
Registered
Joined
·
697 Posts
Discussion Starter #2
i am selling the motor because i have a 460 Stroker motor on my mind and am about to pull the trigger on a build with a builder. i want another motor in the works before anything even gets thought of getting pulled.
 

·
Registered
Joined
·
697 Posts
Discussion Starter #5
How do you like the EX274 cam?
I always thought I might like that in my car is I had more compression.
What brand pistons does it have in it?
i really like the cam and i don't think for a second that it has any lack of low end torque. it pulls hard all the way up until 5500rpms and the max rev is about 6000.

i started gathering parts for this motor over 10 years ago and i believe the pistons are sealed power with a -22 or -24 dish so i'm only at 9.4 cr. i don't think the company requires a cerain compression with it.
 

·
Registered
Joined
·
697 Posts
Discussion Starter #7
motor is pulled and in the middle of my garage and near the door. its always catching my knee walking past it. i want this thing gone before i hyperextend my knee.:mad::mad::mad:

TTT :D
 

·
Registered
Joined
·
697 Posts
Discussion Starter #9
this motor just went thru a re-ring, re-bearing with a new cam/lifters and rockers so i will need to relist this motor. i just broke in the motor yesterday and just reinstalled the inner springs but this motor is already for sale. i am just waiting for my 521 to come back.

i also took a pic of the odometer so i know when i first started the motor and how many miles. and i also video taped the entire break in. i look to only put maybe 300 miles on the motor and maybe 20 passes before my 521 comes back.
 

·
Registered
Joined
·
697 Posts
Discussion Starter #10
521 is close to getting done and this needs to go. i have about 90 miles on the motor and 5 passes on it. ran 12.5xx's in the 1/4, very streetable and nice idle.

must go!

bumpity bump!
 

·
Registered
Joined
·
914 Posts
I wish you werent as far away from pa as you could get. I would buy it. Good deal!

Sent from my SCH-I535 using AutoGuide.Com Free App
 

·
Registered
Joined
·
697 Posts
Discussion Starter #12
I wish you werent as far away from pa as you could get. I would buy it. Good deal!

Sent from my SCH-I535 using AutoGuide.Com Free App
i am willing to budget with the price. i believe people have shipped 351c on the mustang forums from Ohio to california for less than 300.

give me your zip code and maybe we could work something out. i need to get this motor pushed so i don't have a huge piece of metal sitting on the garage floor.

i also have GoPro videos of the break-in process which i can put on youtube for private viewing so you could see if you want to. thanks man.
 

·
Registered
Joined
·
55 Posts
Not interested in the manifold or carb. What would you want for the rest of it shipped truck freight to ZIP 52804? You could tape up the heads and valley and wrap in plastic.

Thanks
 

·
Registered
Joined
·
697 Posts
Discussion Starter #17
Not interested in the manifold or carb. What would you want for the rest of it shipped truck freight to ZIP 52804? You could tape up the heads and valley and wrap in plastic.

Thanks
ummmm, i spent 110 on the used intake, and i bought the carb used at 250 plus 150 getting tuned!!!

let's say $2200 would be a good starting price!!!

for shipping, i'll just call freight quote and get a price from them.
 

·
Registered
Joined
·
697 Posts
Discussion Starter #19
motor is pending sale to a fellow air force military member!!! deposit has been received and just other funds and shipping costing pending.
 
1 - 19 of 19 Posts
Top